Fastener selection guides

Fastener failures rarely start with the wrong part number — they start with a decision made in the wrong order. This section collects our selection guides and the pairing rules we can support with collected specification data, and states plainly where the guides end and a quoted engineering answer has to take over.

The order of a fastener decision

Every guide in this section applies the same decision sequence, because swapping the order is the most common selection mistake we see in inquiries:

  1. Joint type first. Shear joint, clamped joint, sealed joint or location fixture — the load path decides the fastener family (bolts vs pins vs rivets) before any material is discussed.
  2. Material second. Carbon steel, stainless steel (austenitic vs martensitic — they behave differently in both strength and corrosion), aluminium, brass or exotic alloys. The washer material guide walks this choice for the most environment-sensitive part of the joint.
  3. Strength class third. The property class of the bolt sets the minimum class of the nut it threads into — see the pairing table below.
  4. Coating last. Plating and hot-dip galvanizing change dimensions and torque friction; they are chosen after the class pairing is fixed, not before.

Guides in this section

Each guide links onward to the individual specification pages of the families it covers (washers, bolts, screws), where dimension tables and standards references carry the details.

Bolt-to-nut strength class pairing

The one pairing rule that applies across metric hex hardware: the nut property class must be at least that of the bolt. The table below restates the pairing notes collected in our DIN 934 / ISO 4032 dimension and pairing tables; each row is a substitution rule, not a recommendation for your load case.

Bolt property classMinimum nut classCollected pairing note
Property class 8.8Class 8 hex nut (min)A higher nut class may substitute a lower one.
Property class 10.9Class 10 hex nut (min)Same substitution rule; class 10 pairs with 10.9.
Property class 12.9Class 12 hex nut (min)Highest metric pairing in the collected note.
ASTM A325 Type 1 (structural, inch)ASTM A194 Gr. 2H heavy hexHot-dip galvanized A325 takes 2H or A563 DH.
ASTM A490 Type 1 (structural, inch)ASTM A194 Gr. 2H heavy hexHDG is not permitted on A490 — confirm coating at RFQ.

Why the asymmetry? A nut with a lower hardness class strips before the bolt reaches its proof load, and the stripped thread fails without warning. Over-specifying the nut class one step is a common and acceptable substitution; skipping the pairing check entirely is not.

Inch vs metric: why the thread series decides the answer

A 1/2-13 UNF bolt and an M12 bolt are close enough in diameter (12.7 mm vs 12 mm) that cross-threading them together is physically possible — and is a classic failure mode on mixed-stock assembly floors. The threads are not compatible: the flank angles and pitches (1.77 mm vs 1.75 mm pitch at these sizes) differ enough to damage both threads under clamp load. Selection guides therefore always fix the thread system first; our dimension tables keep the inch and metric series in separate columns for exactly this reason. Where a joint mixes systems — common in machinery built to both standards — use a conversion stud or a rated adapter, never a forced thread pair.

Where the guides stop on purpose

These guides are limitations-honest by design. They are not suitable as the sole basis for a safety-critical joint: an operating limit such as sustained vibration, temperatures above roughly 300 °C for standard carbon-steel hardware, or a corrosive environment can invalidate a pairing that looks correct on paper. Application-specific answers — preload values, torque tables, fatigue life — require the joint drawing, and we answer those through a quote, not through a generic table. If a selection question turns on a number the collected specification data does not establish, our pages say "confirm at RFQ" instead of guessing.

Request a Quote

Send us the joint, not just the part number: request a quote with the load type, environment, thread system and standards (ISO, DIN or ASTM) your drawing references, and we will confirm the selection against current stock and collected specification data. Reference our selection guides when you inquire — it shortens the back-and-forth.