US Bolt Grades & Strength Chart — SAE Grades 1–8.2 and ASTM A307/A449/A325/A354/A490, Minimum Strengths
Minimum strength values for US inch-series bolts — SAE Grades 1, 2, 4, 5, 5.2, 7, 8, 8.2 and ASTM A307, A449, A325 (Types 1/2/3), A354 (BC/BD), A490 (Types 1/3) — proof, tensile and yield minimums in ksi per size range, transcribed row-for-row from the collected strength chart.
Last updated: 2026-11
Reference data
Inch-series bolt strength is not one number per bolt — it is a grade-and-size-range pair, and the boundaries matter. The collected chart lays out the US ladder: SAE Grade 2 runs 55 ksi proof / 74 tensile / 57 yield up to 3/4 in, then drops to the Grade 1 set (33/60/36) from 7/8 in — the single most expensive mistake in grade selection, buying a "Grade 2" large bolt that is really a Grade 1 in strength. Grade 5 carries 85/120/92 through 1 in and falls to 74/105/81 (the A449 row) from 1 1/8 in; A325 structural bolts mirror Grade 5 across Types 1, 2 and 3 (weathering steel); Grade 8 and A354 BD hold 120/150/130 across the full 1/4–1 1/2 in range; A354 BC splits 105/125/109 small and 95/115 large with the yield column unprinted on its upper range (flagged). The source notes minimums are those exceeded by 99 percent of fasteners — a statistical floor, not a per-bolt guarantee — and its merged-cell layout groups markings over shared grades (A307 over Grade 1, A449 over the Grade 5 upper ranges). Material callouts reproduce as printed, including the A354 BC row the chart labels "weathering steel, quench and temper" — flagged, since BC is normally alloy steel; verify against the ASTM document before relying on it. Size ranges print in the source's mixed fraction style ("3/2" = 1 1/2 in). What the chart is not: a metric conversion (Grades 5/8 are not property classes 8.8/10.9, the geometry and proof-load definitions differ), a torque table, or a hardness spec — those are RFQ or standards-document items.
| Coverage | 23 grade/size-range rows: SAE Grades 1, 2, 4, 5, 5.2, 7, 8, 8.2; ASTM A307, A449, A325 Types 1/2/3, A354 BC/BD, A490 Types 1/3 — inch series, 1/4 to 4 in by row |
|---|---|
| Minimum strengths (ksi) | Proof / tensile / yield per grade and size range — Grade 2: 55/74/57 to 3/4 in, 33/60/36 from 7/8 in; Grade 5: 85/120/92 to 1 in, 74/105/81 from 1 1/8 in; Grade 8 & A354 BD: 120/150/130; A354 BC: 105/125/109 (1/4–2 1/2 in), 95/115 (2 3/4–4 in, yield not printed) |
| Statistical basis | Source note: minimum strengths are exceeded by 99 percent of fasteners — a reliability floor for the population, not a per-piece guarantee |
| Materials as printed | Low/medium carbon (Grades 1, 2, A307); medium carbon Q&T (Grades 5, 7, A325 Type 1, A449); low-carbon martensite Q&T (5.2, A325 Type 2); weathering steel Q&T (A325 Type 3, A490 Type 3, and A354 BC as printed — flagged); alloy steel Q&T (Grade 8, A354 BD, A490 Type 1) |
| Not in this chart | Proof-load values, hardness ranges, torque specs, metric property-class equivalents and fatigue data are not tabulated — per RFQ (state grade, size range and required certificates) |
| Bolt Grade Marking | Bolt Grade | Bolt Material | Bolt Size Range (in) | Min. Proof Strength (10^3 psi) | Min. Tensile Strength (10^3 psi) | Min. Yield Strength (10^3 psi) |
|---|---|---|---|---|---|---|
| SAE Grade 1 | Low or medium carbon | 1/4 to 3/2 | 33 | 60 | 36 | |
| ASTM A307 | Low carbon | 1/4 to 3/2 | 33 | 60 | 36 | |
| SAE Grade 2 | Low or medium carbon | 1/4 to 3/4 | 55 | 74 | 57 | |
| 7/8 to 3/2 | 33 | 60 | 36 | |||
| SAE Grade 4 | Medium carbon, cold drawn | 1/4 to 3/2 | 65 | 115 | 100 | |
| SAE Grade 5 | Medium carbon, quench and temper | 1/4 to 1 | 85 | 120 | 92 | |
| ASTM A449 | 9/8 to 3/2 | 74 | 105 | 81 | ||
| ASTM A449 | 7/4 to 3 | 55 | 90 | 58 | ||
| SAE Grade 5.2 | Low-carbon martensite, quench and temper | 1/4 to 1 | 85 | 120 | 92 | |
| ASTM A325, Type 1 | Medium carbon, quench and temper | 1/2 to 1 | 85 | 120 | 92 | |
| 9/8 to 3/2 | 74 | 105 | 81 | |||
| ASTM A325, Type 2 | Low-carbon martensite, quench and temper | 1/2 to 1 | 85 | 120 | 92 | |
| 9/8 to 3/2 | 74 | 105 | 81 | |||
| ASTM A325, Type 3 | Weathering steel, quench and temper | 1/2 to 1 | 85 | 120 | 92 | |
| 9/8 to 3/2 | 74 | 105 | 81 | |||
| ASTM A354, Grade BC | Weathering steel, quench and temper | 1/4 to 5/2 | 105 | 125 | 109 | |
| 11/4 to 4 | 95 | 115 | ||||
| SAE Grade 7 | Medium-carbon alloy, quench and temper | 1/4 to 3/2 | 105 | 133 | 115 | |
| SAE Grade 8 | Medium-carbon alloy, quench and temper | 1/4 to 3/2 | 120 | 150 | 130 | |
| ASTM A354, Grade BD | Alloy steel, quench and temper | 1/4 to 3/2 | 120 | 150 | 130 | |
| SAE Grade 8.2 | Low-carbon martensite, quench and temper | 1/4 to 1 | 120 | 150 | 130 | |
| ASTM A490, Type 1 | Alloy steel, quench and temper | 1/2 to 3/2 | 120 | 150 | 130 | |
| ASTM A490, Type 3 | Weathering steel, quench and temper |
- Row 2 (ASTM A307): The source merges the marking and grade cells for ASTM A307 (printed once in the flattened first column); reproduced as a single marking entry with the grade cell left empty.
- Row 4 (): Continuation size-range row (7/8 to 3/2) for the grade above — the source table's merged cells print no marking/grade/material on this line; values belong to the preceding grade row's second size range.
- Row 7 (ASTM A449): Marking "ASTM A449" printed alone in the flattened first column for the 9/8 to 3/2 size range — the source's merged cells carry no separate grade/material on this line (material inherits from the grade row above); reproduced with marking, size range and strengths only.
- Row 8 (ASTM A449): Marking "ASTM A449" printed alone in the flattened first column for the 7/4 to 3 size range — the source's merged cells carry no separate grade/material on this line (material inherits from the grade row above); reproduced with marking, size range and strengths only.
- Row 11 (): Continuation size-range row (9/8 to 3/2) for the grade above — the source table's merged cells print no marking/grade/material on this line; values belong to the preceding grade row's second size range.
- Row 13 (): Continuation size-range row (9/8 to 3/2) for the grade above — the source table's merged cells print no marking/grade/material on this line; values belong to the preceding grade row's second size range.
- Row 15 (): Continuation size-range row (9/8 to 3/2) for the grade above — the source table's merged cells print no marking/grade/material on this line; values belong to the preceding grade row's second size range.
- Row 16 (): Source prints the A354 Grade BC material as "Weathering steel, quench and temper" while Grade BD two rows down is "Alloy steel, quench and temper" — Grade BC is normally alloy (or weathering for Type 3-style variants); reproduced as printed, verify material callout against ASTM A354.
- Row 17 (): Continuation size-range row (11/4 to 4) for the grade above — the source table's merged cells print no marking/grade/material on this line; values belong to the preceding grade row's second size range. The yield column is not printed for this size range.
How to use it
- Grade material callouts are as printed on the chart (see specs); material certification — mill test report per EN 10204 3.1 or equivalent — is an RFQ line, not a chart value
These figures are engineering reference data, not a stocked-range claim. Parts manufactured or sourced to the standards named here are quoted on request — send an RFQ with your sizes, grades and quantities and the quote carries the confirmed schedule and documents.
Frequently asked questions
Why does a bolt's strength change with diameter inside one grade, and how do I read this chart correctly when specifying?
Because bigger bolts cannot reach the same strength per unit area with the same heat treatment and quench depth — the standards deliberately lower minimums in steps as diameter grows. That is why Grade 2 carries 55 ksi proof through 3/4 in and only 33 ksi from 7/8 in (at which point it is chemically and mechanically the Grade 1 set), and Grade 5 steps down from 85 to 74 ksi proof at 1 1/8 in. Reading the chart is therefore always a two-column lookup: find the grade, then the size range your diameter falls in — quoting "Grade 5, 85 ksi proof" for a 1 1/4 in bolt is wrong before the fastener is even made. The second reading discipline is the chart's grouping: several markings share one grade row (A307 over Grade 1; A449 over Grade 5's upper ranges; A325 mirroring Grade 5 across three material types) and the merged layout continues a grade across a second size-range line with only the strengths printed — those continuation rows are flagged on the table below. Third, treat the numbers as what the source says they are: minimums exceeded by 99 percent of fasteners, a population floor for design margins rather than a promise about any single bolt. And keep the chart inside its world: SAE/ASTM grades do not convert to ISO property classes by dividing — different test geometry, different proof-load definitions — so a joint spanning the two systems needs both sets of documents. Hardness ranges and torque values live outside this chart; bring them to RFQ with the grade and size callout.
What is the MOQ and lead time for bolts to these grades?
The minimum order quantity for US Bolt Grades & Strength Chart — SAE Grades 1–8.2 and ASTM A307/A449/A325/A354/A490, Minimum Strengths is 1,000–10,000 pieces depending on size. Stock items of US Bolt Grades & Strength Chart — SAE Grades 1–8.2 and ASTM A307/A449/A325/A354/A490, Minimum Strengths ship in 3–7 days; high-strength and custom parts in 15–25 days. Common grades and sizes of US Bolt Grades & Strength Chart — SAE Grades 1–8.2 and ASTM A307/A449/A325/A354/A490, Minimum Strengths are widely stocked; confirm the exact schedule against quantity and size mix at quotation.