Bolt Edge Distance and Spacing — BS 5950 Legacy Data
Minimum bolt edge distances and pitch spacing per BS 5950 legacy practice, M 12 to M 36 — clearance hole, pitch A and minimum edge distances B and C for preliminary plate layout.
Last updated: 2026-11
Reference data
Where a bolt sits in a plate is a design decision with minimums: too close to the edge and the plate tears out in bearing, too sparse and the joint grows for no reason. This reference tabulates the BS 5950 (structural steelwork, legacy) minimums per bolt size M 12 to M 36: the clearance hole diameter (M 16: 18 mm), the pitch A between bolts (40 mm at M 16, scaling to 90 mm at M 36), and two minimum edge distances — B, measured to the edge in the direction of force (26 mm at M 16), and C, the transverse edge distance (23 mm at M 16). The pattern is consistent across the ladder: pitch runs about 2.5 diameters, edge distance B about 1.6-1.75 diameters, C slightly less. These are legacy-code minimums — a preliminary layout that respects them can later be refined against the governing current code (Eurocode 3, AISC) without rework in most cases. The table gives minimums, not recommendations: rolled-edge, sheared-edge and weathering conditions can push the working values up. Plate supply and drilled/cut layouts are quoted per RFQ against your actual stack-up.
| Code basis | BS 5950 legacy data, as collected |
|---|---|
| Size range | M 12 to M 36, 7 sizes |
| Columns | Clearance hole D, pitch A, minimum edge distance B (in-force direction), minimum edge distance C (transverse) |
| Worked example | M 20: hole 22 mm, pitch 50 mm, edge B 31 mm, edge C 28 mm |
| Not tabulated | Current-code (Eurocode 3 / AISC) values, rolled vs sheared edge factors, multiple-row spacing rules — per RFQ |
| Bolt Size | Clearance Hole D | Pitch A | Minimum Edge B | Minimum Edge C |
|---|---|---|---|---|
| M12 | 14 | 30 | 20 | 18 |
| M16 | 18 | 40 | 26 | 23 |
| M20 | 22 | 50 | 31 | 28 |
| M24 | 26 | 60 | 37 | 33 |
| M27 | 30 | 68 | 42 | 38 |
| M30 | 33 | 75 | 47 | 42 |
| M36 | 39 | 90 | 55 | 49 |
How to use it
- Edge-distance minimums interact with plate material and edge preparation: sheared or flame-cut edges, weathering grades and thin plate all shift the safe working value upward from these BS 5950 legacy minimums. When you RFQ drilled plates, tell us the bolt size, hole type (standard/oversize/slotted), edge condition and the governing code so the layout is cut to the right margins the first time
These figures are engineering reference data, not a stocked-range claim. Parts manufactured or sourced to the standards named here are quoted on request — send an RFQ with your sizes, grades and quantities and the quote carries the confirmed schedule and documents.
Frequently asked questions
What is the difference between edge distance B and C, and how do I apply them?
B is the minimum distance from the bolt centre to the plate edge measured in the direction of the transmitted force — the direction where bearing tear-out happens — and C is the minimum to an edge perpendicular to the force. For M 24: B 37 mm, C 33 mm, pitch 60 mm, hole 26 mm. Both must be satisfied at every bolt; the pitch A applies between adjacent bolts along the load path. A quick layout rule from the table: hole size + roughly 1.2 to 1.4 diameters to the edge. Remember these are BS 5950 legacy minimums — they are a floor for preliminary layout, and current codes, edge preparation (sheared vs machined) and corrosion protection can all demand more. If your connection is code-governed, the code's table governs; this page is the cross-check that catches an impossible layout before fabrication.
Can I reduce edge distances if I use oversize holes or slotted holes?
No — oversize and slotted holes make edge distances more demanding, not less: the hole removes more plate area near the edge, so the bearing tear-out risk the B/C minimums guard against rises. The BS 5950 legacy table here tabulates standard clearance holes (M 27 bolt: 30 mm hole); with oversize or short-slotted holes, good practice keeps the edge distance measured from the hole edge to at least the tabulated margin, and slotted holes transverse to the load usually need the next size up in edge distance. The safe sequence: lay out with this table's minimums, check the holes you actually need against the governing code's oversize/slotted rules, and only then cut. Quote hole type and edge distances explicitly on the RFQ so the plates arrive drilled to a layout that passes inspection.