U-Bolts

U-bolts for pipe clamping and support in waterworks and mechanical services — measured per the IFI-136 convention by four dimensions (length, hook, diameter, thread length), covering pipe sizes 1/2–36 in with rod diameters 1/4–1 in, in A36 carbon steel, A193 alloy and 304/316 stainless.

Last updated: 2026-11

Request a Quote

U-Bolts in an industrial setting
Illustrative image redrawn from real product references — not a photograph of stocked items.

Specifications

Industry-standard reference ranges — availability confirmed per quotation; not a stocked-range claim.

pipe size range 1/2–36 in waterworks pipe sizes (IFI-136 chart)
rod diameter 1/4–1 in rod diameter across the chart
measurement Four dimensions per IFI-136: length (end of bolt to inside of bend), hook (distance between legs), diameter (one leg), thread length

Materials

  • A36 carbon steel
  • A193 alloy steel
  • 304 stainless steel
  • 316 stainless steel

Engineering guidance

A U-bolt is a bent rod that behaves like four decisions: the hook that wraps the pipe, the rod diameter that carries it, the thread length that clamps it, and the material that survives the environment. The sections below carry the ordering rules; the per-size chart rows live under Specifications.

Four dimensions, one convention

U-bolts are measured by four dimensions, per the IFI-136 convention the collected chart follows: length (from the end of the bolt to the inside of the bend), hook (the distance between the legs), diameter (of one leg), and thread length. Two drawing traps live in the hook: some drawings show it at the center or bottom of the bolt, and some measure hook center-to-center of the legs rather than inside-to-inside — so a drawing dimension that disagrees with the chart by one rod diameter may be a convention difference, not an error.

State all four dimensions on the RFQ. Ordering by pipe size alone leaves the hook and thread length open, and those are the two dimensions a wrap, liner or saddle changes.

Reading the chart: rod grows with pipe

The collected waterworks chart runs 1/2 in to 36 in pipe. The rod diameter steps up with the pipe — 1/4 in rod through 1 in pipe, 3/8 in through 2 in, 1/2 in through 5 in, 5/8 in at 6–8 in, 3/4 in at 10 in, 7/8 in at 12–16 in, and 1 in from 18 in up — while thread length grows more slowly (2 3/8 in at the small end to 4 3/4 in at the top of the range). Treat the chart as the convention set for standard waterworks supports: a pipe with coating allowance, an insulated line or a non-standard OD changes the hook, so those quote from the actual dimensions.

The chart is a reference for sizing, not a substitute for the joint design: support spacing, load per support and thermal movement belong to the piping design, and the U-bolt dimensions follow from it.

Material is the corrosion budget

The collected spec library lists U-bolts in A36 carbon steel, A193 alloy and 304/316 stainless steel. Carbon steel carries the standard waterworks support duty (typically galvanized or plated — the coating is the corrosion budget, spent where the pipe contacts the legs); 304/316 stainless moves the budget to the base metal for corrosive, coastal or wash-down environments, at which point the dimensions stay the same and only the grade line on the order changes.

What this page cannot verify: coating weights or salt-spray hours for any specific U-bolt lot, and the fit of a non-standard pipe OD against the chart's assumed dimensions — both confirm at quotation against the actual pipe specification.

Ordering & documentation

Documents

Shipments of U-Bolts are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for this u-bolts line follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.

Quotation

  • Supported pipe outside diameter or NPS/schedule and required U-bolt inside width/radius.
  • Rod diameter, leg length, thread length and bend geometry from the support drawing.
  • Material/grade, coating and service environment.
  • Support load, saddle/plate arrangement, quantity and destination.

Sample & supply

Minimum order quantities and lead times for u-bolts are confirmed at quotation — send pipe size, rod diameter, hook, length and thread length on the RFQ and the quote will carry a firm schedule; sample availability is confirmed with the quotation.

Storage & shipping

U-Bolts are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store these u-bolts dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.

Frequently asked questions

How is a U-bolt specified and measured?

By four dimensions per the IFI-136 convention the collected chart follows: length (from the end of the bolt to the inside of the bend), hook (the distance between the legs — note some drawings measure it center-to-center of the legs), diameter (of one leg), and thread length. State all four on the RFQ; pipe size alone leaves the hook and thread length open.

Which pipe sizes does the collected chart cover?

The collected waterworks chart runs from 1/2 in pipe (1/4 in rod, 15/16 in hook, 3 1/4 in length) to 36 in pipe (1 in rod, 36 1/8 in hook, 39 11/16 in length), all in inches. Intermediate sizes step through 3/8, 1/2, 5/8, 3/4, 7/8 and 1 in rod diameters as the pipe grows — quote from the actual OD and coating allowance of your pipe if it differs from the chart's assumptions.

What materials are U-bolts carried in?

The collected spec library lists U-bolts in A36 carbon steel, A193 alloy and 304/316 stainless steel. Carbon steel (typically galvanized or plated) covers standard waterworks supports; 304/316 stainless suits corrosive or coastal environments — the grade choice governs the corrosion budget, while the IFI-136 dimensions are the same.

Request a Quote

Get factory-direct pricing from the manufacturer.

What to include in your U-Bolts inquiry

  • ✓ Give the supported pipe outside diameter or NPS/schedule and the required U-bolt inside width/radius.
  • ✓ Specify rod diameter, leg length, thread length and bend geometry from the support drawing.
  • ✓ State material/grade, coating and the service environment.
  • ✓ Describe support load, saddle/plate arrangement, quantity and destination.
  • ✓ Factory-direct pricing for your U-Bolts
  • ✓ Standard and custom specifications
  • ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
  • ✓ Full fastener family support

We use your details only to answer this inquiry — see our Privacy notice for everything the form collects.