ASTM F3393 Zinc-Flake Coating Systems

ASTM F3393 — Zinc-Flake Coating Systems for Fasteners. The current structural-bolting zinc-flake standard: accepted for high-strength structural bolting assemblies by the RCSC 2025 Specification (Corrosion D, Appearance 1, Coefficient of Friction R) and, since the 2025 edition, the replacement for ASTM F1136, F2833 and F3019.

Last updated: 2026-11

Request a Quote

ASTM F3393 Zinc-Flake Coating Systems in an industrial setting
Illustrative image redrawn from real ASTM F3393 Zinc-Flake Coating Systems product references — not a photograph of stocked items.

Specifications

ASTM F3393 is the zinc-flake coating standard structural engineers now cite for high-strength bolting. The RCSC Specification for Structural Joints Using High-Strength Bolts (June 5, 2025 edition) accepts zinc-flake coating "complying with ASTM F3393, Corrosion D, Appearance 1, Coefficient of Friction R" applied before installation, and its commentary records that F3393 replaced the three coating standards cited in prior editions — ASTM F1136, F2833 and F3019 (see F3393 Appendix X.1). Because zinc flake is non-electrolytic, it carries none of the hydrogen-embrittlement risk of plating: investigations per IFI-144 presented to the ASTM F16 committee showed that F3393 zinc-flake coating on ASTM F3125 Grade A490 bolts does not cause delayed cracking by internal hydrogen embrittlement, nor accelerate environmental hydrogen embrittlement. RCSC handling rules matter as much as the coating itself: every threaded component of an assembly must be coated by the same process, coated nuts are over-tapped per ASTM A563, and coated bolts and nuts are treated as a matched bolting assembly.

Standard ASTM F3393 — Zinc-Flake Coating Systems for Fasteners (current edition F3393-24)
Structural acceptance Permitted by RCSC Specification Section 2.8.2 (2025 edition) applied prior to installation, classification Corrosion D, Appearance 1, Coefficient of Friction R
Replaced standards Replaced ASTM F1136, ASTM F2833 and ASTM F3019 as the coating standards cited by RCSC (2025 edition commentary; see F3393 Appendix X.1)
Same-process rule All threaded components of a bolting assembly shall be coated by the same process (RCSC 2.8.2)
Nuts Zinc-flake coated nuts over-tapped in accordance with ASTM A563 (RCSC 2.8.2.2)
Direct tension indicators Zinc-flake on DTIs only with the DTI manufacturer's approval (RCSC 2.8.2.3); spline-end twist-off and fixed assemblies coated only under the manufacturer's direction (RCSC 2.8.2.1)
Mechanical compatibility Tested not to degrade the performance of Group 150 bolts; RCSC notes inclusion in its table does not imply any specific corrosion-protection performance
Hydrogen embrittlement None from application — non-electrolytic; IFI-144 investigations on F3125 Grade A490 showed no internal-HE delayed cracking and no acceleration of environmental HE
Matched-assembly factors RCSC commentary: coating effect on mechanical properties, over-tapping effect on nut stripping strength, and coating/lubrication effect on pretensioning torque

Materials

  • High-strength structural bolts (ASTM F3125 Grades A325/A490 type, Group 120/144/150)
  • Structural heavy hex nuts (over-tapped per ASTM A563)
  • Hardened washers and threaded assemblies of matched bolting sets

Ordering & documentation

Documents

Shipments of ASTM F3393 Zinc-Flake Coating Systems are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for ASTM F3393 Zinc-Flake Coating Systems orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.

Quotation

  • The product family (ASTM F3393 Zinc-Flake Coating Systems), product standard/designation and drawing or part number.
  • The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
  • Material/grade, heat-treatment condition and surface finish, together with the service environment.
  • Quantity per size, delivery destination and required test or traceability documents.

Sample & supply

Minimum order quantity for astm f3393 zinc-flake coating systems is per batch, carried with the fastener order (applies to the standard sizes and finishes for astm f3393 zinc-flake coating systems; mixed, special or custom variants are quoted — final commercial terms per quotation) Finishing for astm f3393 zinc-flake coating systems run adds 5–10 days to the fastener lead time. Quantities or variants of astm f3393 zinc-flake coating systems outside the standard range are confirmed at quotation.

Storage & shipping

Coated parts are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store finished fasteners dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.

Frequently asked questions

Why does the RCSC Specification still require over-tapped nuts when zinc-flake coatings are thin?

Because even a thin coating consumes thread clearance. The RCSC commentary is explicit that zinc-flake coatings are thin yet over-tapping the nuts remains necessary, comparing the even, uniformly distributed deposit to mechanical galvanizing. It also frames the three factors a coated assembly must be judged on: the coating process's effect on the bolting material's mechanical properties, the effect of over-tapping on the nut's stripping strength, and the effect of coating plus lubrication on the torque needed to reach pretension.

My drawing calls out ASTM F1136 — do I substitute F3393?

F1136 was withdrawn in 2025 and replaced by F3393, so new callouts should read F3393 (RCSC points to F3393 Appendix X.1 for the transition). F1136 Grade 3 — the chromate-free grade — carried a 720-hour minimum salt-spray requirement closely equivalent to ISO 10683, and the two were treated as near-interchangeable with test-method differences documented. Substitute only with the customer's confirmation on record: name the F3393 classification the joint expects (RCSC cites Corrosion D, Appearance 1, Coefficient of Friction R), keep friction class and lubrication requirements intact, and document the change on the drawing.

Can F3393-coated bolts be embedded in concrete?

Flag it to the Engineer of Record when the coating contains aluminum. The RCSC commentary warns that wet, freshly hardened concrete (less than 7 days old) is alkaline enough to react with free aluminum, evolving hydrogen gas that consumes the aluminum and can lead to wormholes in the concrete; whether the aluminum bound within a zinc-flake coating is susceptible has not been determined by research to date. This applies even though these bolts are typically not used embedded — the EOR should address it explicitly.

What is the MOQ and lead time for this finish?

Finishing runs per batch carried with the fastener order and adds 5–10 days to the fastener lead time. Coated parts follow the finish line that processes them, so confirm the exact schedule against quantity and finish class at quotation.

What should an RFQ for this finish state?

State the base fastener (grade, diameter, length), the coating standard and class (for example ASTM B841 Class 2 with black trivalent passivate, or ISO 10683 with a specified topcoat), any thickness or salt-spray requirement, lubrication or torque-tension needs, and quantity per size — plus destination country and required documents such as a mill test certificate.

Request a Quote

Get factory-direct pricing from the manufacturer.

What to include in your ASTM F3393 Zinc-Flake Coating Systems inquiry

  • ✓ Identify the base fastener material/grade and substrate condition before coating.
  • ✓ Name the coating process and governing specification, with required coating thickness and any post-treatment.
  • ✓ Define corrosion acceptance explicitly: test method, exposure duration, and whether white corrosion or red rust is the rejection criterion.
  • ✓ State any friction-coefficient, torque-tension, temperature or hydrogen-embrittlement controls relevant to the joint.
  • ✓ Factory-direct pricing for your ASTM F3393 Zinc-Flake Coating Systems
  • ✓ Standard and custom specifications
  • ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
  • ✓ Full fastener family support

We use your details only to answer this inquiry — see our Privacy notice for everything the form collects.