DIN 983 External Retaining Rings with Lugs

DIN 983 grooved external retaining rings with lugs for shafts 16-140 mm: ring thickness s, groove diameter d3, lug height a, body height b, lug hole d5, groove width m (H13), static loads FN/FR/Fhg in kN and the matching DIN 5254 plier size per shaft — the external-with-lugs metric ladder.

Last updated: 2026-11

Request a Quote

DIN 983 External Retaining Rings with Lugs in an industrial setting
Illustrative image redrawn from real DIN 983 External Retaining Rings with Lugs product references — not a photograph of stocked items.

Specifications

DIN 983 is the external retaining ring that grips a shaft groove with its own lugs for grip during assembly — the counterpart that pairs with the internal-with-lugs DIN 984 already in the catalog. The collected ladder runs shaft diameters d1 16 through 140 mm in 40 rows: ring thickness s steps 1 / 1,2 / 1,5 / 1,75 / 2 / 2,5 / 3 / 4 mm across the ladder, the groove diameter d3 sits 1,3-1,5 mm under the shaft nominal (14,7 at d1 16 up to 133 at d1 140), the groove width m grows from 1,1 mm (H13) at the 16 mm end to 4,15 mm at 120-130, and the load columns — FN, FR and Fhg, printed in kN where the source annotates them — climb from single digits at the small end to the hundreds around 110-140 mm. Every row carries the nominal size of the DIN 5254 circlip pliers that fits it (10 at d1 16-18, 19 through the 1,2-1,5 mm bands, 40 across the 1,75-2,5 mm middle, 85 from d1 85, 125 on the two largest rows), so assembly tooling is selectable straight off the ladder. Where a design needs lug-assisted external retention on a metric shaft — serviceable assemblies, vertical shafts, anywhere a snap-on ring must come back off — this is the identity; where the bore is the retained side, that is DIN 984.

Series / scope DIN 983 external retaining rings with lugs (grooved), metric shafts d1 16-140 mm, 40 sizes — ring and groove geometry with FN/FR/Fhg static loads and DIN 5254 plier sizes
Ring thickness s 1 / 1,2 / 1,5 / 1,75 / 2 / 2,5 / 3 / 4 mm by size band; the s column header prints "Lim. Dex." and the band tolerance spans (e.g. 0 -0,06 at 16-38, 0 -0,1 at 110-140) as printed
Groove diameter d3 / width m d3 14,7 (d1 16) to 133 (d1 140), band tolerances carried verbatim; m 1,1 to 4,15 mm, printed H13
Lug geometry a / b / d5 a (foot-ring height) max 3,5-14,2; b (body height) approx 2,3-11,2; d5 (lug hole) min 1,7-4 — per the collected legend terms
Loads and speed FN and FR in kN from 3,26/7 at d1 16 up the ladder; Fhg kN and nabl min-1 printed per row; t, d4 and g print without legend or unit entries — header words carried verbatim
Assembly tooling DIN 5254 pliers nominal size per row: 10 (d1 16-18), 19 (19-35), 40 (38-80), 85 (85-120), 125 (130-140)
Not tabulated Materials beyond "Steel: steel" (stainless/plastic/non-ferrous print "-"), dynamic or shock derating, internal-ring counterpart geometry (DIN 984 / DIN 472 identities) — per RFQ
DIN 983 external retaining rings with lugs - per-size dimensions (dimensions in mm, per the collected page)Header rows carried from the collected page: group spans "Shaft diameter, d1 / Circlip / Groove / Design criteria", per-column names, and the tolerance/unit row ("Lim. Dex.", "lim.dev.", "max.", "approx.", "min.", "H13", "kN", "min-1"). FN/FR/Fhg print kN, nabl prints min-1; t, d4 and g print no unit entry. Dimensions in mm per the page statement; all cells verbatim, decimal commas preserved.
d1 (Nominal size)ss (Lim. Dex.)d3d3 (lim.dev.)a (max.)b (approx.)d5 (min.)Mass of 1000 units, in kg (approx.)d2d2 (lim.dev.)m (H13)tn (min.)d4FN (kN)FR (kN)gFhg (kN)nabl (min-1)Nominal size of pliers as in DIN 5254
1610-0,0614,7+0,1-0,363,52,31,70,8215,20-0,111,10,41,223,43,26712,34540010
1710-0,0615,7+0,1-0,363,62,31,70,9316,20-0,111,10,41,224,63,46812,44090010
181,20-0,0616,5+0,1-0,363,72,421,24170-0,111,30,51,525,84,58171,53,753780010
191,20-0,0617,5+0,1-0,363,72,521,35180-0,111,30,51,526,84,84171,53,83340019
201,20-0,0618,5+0,13-0,423,82,621,45190-0,131,30,51,5285,0617,11,53,853040019
221,20-0,0620,5+0,13-0,4242,821,77210-0,131,30,51,530,45,6516,91,53,82570019
231,20-0,0621,5+0,21-0,424,12,921,84220-0,211,30,51,531,65,916,61,53,82380019
241,20-0,0622,2+0,21-0,424,2321,9822,90-0,211,30,551,732,86,7516,11,53,652510019
251,20-0,0623,2+0,21-0,424,3322,1223,90-0,211,30,551,7347,0516,21,53,72420019
261,20-0,0624,2+0,21-0,424,43,122,1824,90-0,211,30,551,735,27,3416,11,53,72240019
281,50-0,0625,9+0,21-0,424,53,223,1526,60-0,211,60,72,137,51032,11,57,52020019
301,50-0,0627,9+0,21-0,424,73,523,6528,60-0,211,60,72,139,910,7332,11,57,651790019
321,50-0,0629,6+0,21-0,4253,62,5430,30-0,251,60,852,642,515,8531,225,551550019
351,50-0,0632,20,25-0,55,23,92,54,38330-0,251,61345,917,830,825,551480019
381,750-0,0635,20,25-0,55,54,22,56,5360-0,251,851349,619,349,529,11290019
401,750-0,0636,5+0,39-0,97,24,42,5737,50-0,251,851,253,855,125,35129,51350040
421,750-0,0638,5+0,39-0,97,24,52,57,539,50-0,251,851,253,857,126,75029,451260040
451,750-0,0641,5+0,39-0,97,24,72,58,542,50-0,251,851,253,860,128,64929,351100040
471,750-0,0643,5+0,39-0,97,24,92,58,744,50-0,251,851,253,862,13049,529,551000040
481,750-0,0644,5+0,39-0,97,252,58,945,50-0,251,851,253,863,130,749,429,55905040
5020-0,0745,8+0,39-0,98,25,12,511,5470-0,252,151,54,567,23873,3214,41000040
5520-0,0750,8+0,46-1,18,25,42,513520-0,32,151,54,572,24271,42,511,4846040
5720-0,0752,8+0,46-1,18,25,52,514540-0,32,151,54,574,243,770,92,511,4800040
5820-0,0753,8+0,46-1,18,25,62,514,3550-0,32,151,54,575,244,371,12,511,5775040
6020-0,0755,8+0,46-1,18,25,82,514,8570-0,32,151,54,577,24669,22,511,3720040
622,50-0,0757,8+0,46-1,18,262,515,9590-0,32,151,54,579,247,569,32,511,45680040
652,50-0,0760,8+0,46-1,110,26,3321,7620-0,32,651,54,586,449,8135,62,522,7630040
672,50-0,0762,5+0,46-1,110,26,4322,6640-0,32,651,54,588,451,3136,12,523680040
682,50-0,0763,5+0,46-1,110,26,5323,5650-0,32,651,54,589,452,2135,92,523,1660040
702,50-0,0765,5+0,46-1,110,26,6325,1670-0,32,651,54,591,453,8134,22,523620040
752,50-0,0770,5+0,46-1,110,27328,2720-0,32,651,54,596,457,61302,522,8550040
802,50-0,0774,5+0,46-1,110,27,4330,8760-0,32,651,755,3101,471,6128,4319,5580040
8530-0,0879,5+0,46-1,110,27,83,539,581,50-0,353,151,755,3106,476,2215,4333,4520085
9030-0,0884,5+0,54-1,310,28,23,547,786,50-0,353,151,755,3111,480,8217,2334,4475085
9530-0,0889,5+0,54-1,310,28,63,55391,50-0,353,151,755,3116,485,5212,23,529,25425085
10030-0,0894,5+0,54-1,310,293,556,696,50-0,353,151,755,3121,490206,43,529400085
11040-0,1103+0,54-1,312,29,63,5841060-0,544,152635,61134573,566,9415085
12040-0,1113+0,54-1,314,210,23,589,71160-0,544,1526149,8123,5424,63,564,5350085
13040-0,1123+0,63-1,514,210,741051260-0,634,1526159,8134395,5455,23050125
14040-0,1133+0,63-1,514,211,241151360-0,634,1526169,8144,5376,5454,42640125
  • Legend coverage gap: the collected page legend explains only a, d5, s, b, d3; d2, m, t, n, d4, FN, FR, g, Fhg, nabl have no legend entry and t/d4/g also no unit-row entry - labels are the source header words verbatim.
  • The s column header prints "Lim. Dex." (source spelling, carried verbatim).
  • Row 37 (110): Row d1=110 prints d4 35,6 / FN 113 / FR 457, discontinuous against d1=100 (121,4 / 90 / 206,4) and d1=120 (149,8 / 123,5 / 424,6) - transcribed as printed, not normalized; verify against the standard before engineering use.
  • Row 14 (35): Row d1=35 prints its a tolerance as "0,25-0,5" without the "+" sign prefix the surrounding band rows carry - as printed.
  • Makings list "Steel: steel" only; stainless/plastic/non-ferrous/thread print "-" on the collected page.

Materials

  • The collected page lists steel only (its Makings row prints stainless, plastic, non-ferrous and thread as "-"). Ring steel assumes the shaft groove is cut to the tabulated d3/m in a material that carries the groove edge loading; the FN/FR/Fhg figures are static ratings and shock or vibration service needs derating the standard does not tabulate here. Ring diameters sit slightly under the shaft nominal so the ring snaps to grip — confirm groove inspection per the H13 width print. Specify material class and groove tolerance on the RFQ.

Ordering & documentation

Documents

Shipments of DIN 983 External Retaining Rings with Lugs are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for DIN 983 External Retaining Rings with Lugs orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.

Quotation

  • The product family (DIN 983 External Retaining Rings with Lugs), product standard/designation and drawing or part number.
  • The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
  • Material/grade, heat-treatment condition and surface finish, together with the service environment.
  • Quantity per size, delivery destination and required test or traceability documents.

Sample & supply

Minimum order quantities and lead times for din 983 external retaining rings with lugs are confirmed at quotation — send ring type, shaft or housing diameter and groove dimensions on the RFQ and the quote will carry a firm schedule; sample availability is confirmed with the quotation.

Storage & shipping

DIN 983 External Retaining Rings with Lugs are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store din 983 external retaining rings with lugs dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.

Frequently asked questions

When does DIN 983 beat the plain external ring DIN 471 — and when not?

The lugs are the difference. Both rings seat in the same kind of shaft groove; DIN 983 adds two lug holes (d5) and a foot ring that let pliers grip the ring for installation and removal, while DIN 471's lugless form spreads the grip around the ring's own ears. Choose DIN 983 where the ring will be serviced — assemblies opened in the field, vertical or accessible shafts where a dropped ring matters, production jigs that install hundreds of rings a day — the DIN 5254 plier size printed on every row of the ladder exists exactly for that. Choose the lugless ring where package size or a recessed groove makes pliers awkward and the ring goes in once. The collected grid gives both the geometry and the static loads to compare on your shaft size directly.

The table's load columns carry a discontinuity around d1=110 — which numbers can I use?

Read the ladder as printed, but treat the d1=110 row with care: it prints d4 35,6 / FN 113 / FR 457, a step that does not sit between its neighbours d1=100 (121,4 / 90 / 206,4) and d1=120 (149,8 / 123,5 / 424,6), and the collected page flags nothing about it — this page transcribes the source verbatim and flags the discontinuity rather than smoothing it. The practical rule for any retaining-ring ladder: the static rating you design to is the smaller of the ring-side and groove-side figures for your exact row, and any row that prints out of family deserves a second source before it enters a drawing. Rows outside the discontinuity follow the expected pattern — loads climbing with ring section, FN/FR kN annotated, Fhg kN and nabl min-1 printed per row — and t, d4, g carry no unit or legend entries, so those columns are geometry references, not rated numbers, until a source states otherwise.

What should an RFQ for DIN 983 rings state?

State the standard (DIN 983 external with lugs), the shaft nominal diameter and its groove as machined (groove diameter d3 and width m from your drawing), the ring material class — the collected sheet lists steel; stainless or other classes are quoted from current stock — the DIN 5254 plier size if tooling should match the ladder, and quantity per size. Commercial terms are confirmed at quotation.

Request a Quote

Get factory-direct pricing from the manufacturer.

What to include in your DIN 983 External Retaining Rings with Lugs inquiry

  • ✓ Identify external shaft rings (for example DIN 471) or internal bore rings (for example DIN 472), plus ring type.
  • ✓ Give nominal shaft or housing-bore diameter and the groove diameter, width and tolerances.
  • ✓ State ring material, heat treatment and finish for the service environment.
  • ✓ Describe axial load, rotational speed, assembly access/pliers and quantity per size.
  • ✓ Factory-direct pricing for your DIN 983 External Retaining Rings with Lugs
  • ✓ Standard and custom specifications
  • ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
  • ✓ Full fastener family support

We use your details only to answer this inquiry — see our Privacy notice for everything the form collects.