IFI 130 Structural Splitting Blind Rivets, Regular and Large Head (Self-Plugging, Pull Mandrel)

IFI 130-2003 regular and large head structural splitting self-plugging pull mandrel blind rivets: inch nominal sizes 3/16 and 1/4 with shank/head/mandrel diameters for both head styles and the minimum grip ladder.

Last updated: 2026-11

Request a Quote

IFI 130 Structural Splitting Blind Rivets, Regular and Large Head (Self-Plugging, Pull Mandrel) in an industrial setting
Illustrative image redrawn from real IFI 130 Structural Splitting Blind Rivets, Regular and Large Head (Self-Plugging, Pull Mandrel) product references — not a photograph of stocked items.

Specifications

IFI 130 is the inch-series standard for structural splitting blind rivets — the self-plugging, pull-mandrel type whose body splits back as the mandrel pulls, spreading the shank inside the hole so the set rivet fills it rather than just sitting in it. That splitting action is what puts these in structural sheet-metal and trailer/panel work where an ordinary open-end rivet's straight shank would under-fill the hole. The collected 2003-edition table carries two nominal sizes, 3/16 and 1/4 (read vertically by the d max/min rows: 0.191/0.185 and 0.255/0.248 in), each in two head styles: regular head (dk max 0.405 / 0.535) and large head (dk max 0.587 / 0.775 — the wider bearing face for thin or soft sheet), with head height k max 0.103 / 0.126 (the large-head height prints the same values), mandrel d1 0.116 / 0.151, and minimum grip L1 1.000 in for both sizes. Note the head-height rows print identical values for the two styles — the styles differ in diameter, not height. The minimum grip is the floor, not the range: the length ladder beyond 1.000 in is per RFQ against the actual stack-up.

Standard / scope IFI 130-2003 regular and large head structural splitting self-plugging pull mandrel blind rivets — inch series, nominal sizes 3/16 and 1/4 as tabulated
Shank d max/min 0.191/0.185 (3/16), 0.255/0.248 (1/4) — the size identification, read vertically
Regular head dk max/min 0.405/0.375 (3/16), 0.535/0.485 (1/4)
Large head dk max/min 0.587/0.537 (3/16), 0.775/0.725 (1/4) — wider bearing face for thin or soft sheet
Head height k / mandrel d1 k max/min 0.103/0.083 (3/16), 0.126/0.106 (1/4) — identical values printed for regular and large head; d1 max 0.116/0.151
Grip L1 min 1.000 in for both nominal sizes; length ladder beyond the minimum per RFQ
Not tabulated Load/shear ratings, grip range ladder, material and finish calls — per RFQ
IFI 130-2003 regular and large head structural splitting self-plugging pull mandrel blind rivets — attribute ladder by sizeInch dimensions. The source prints an attribute-label grid positionally paired with a numeric grid; merged rows carry the label cells verbatim followed by the values. Head dimensions print separately for the regular and the large head; sizes are inch nominal 3/16 and 1/4, read vertically. L 1 min (grip) prints 1.000 for both sizes; the grip ladder beyond the minimum is per RFQ.
AttributeSub-label
ddNominal SizeNominal Size3/161/4
ddmaxmax0.1910.255
ddminmin0.1850.248
d kd kRegular headmaxmax0.4050.535
d kd kRegular headminmin0.3750.485
d kd kLarge headmaxmax0.5870.775
d kd kLarge headminmin0.5370.725
kkRegular headmaxmax0.1030.126
kkRegular headminmin0.0830.106
kkLarge headmaxmax0.1030.126
kkLarge headminmin0.0830.106
d 1d 1d 1d 10.1160.151
L 1L 1minmin1.0001.000
  • The label grid mixes four-cell rows (attribute + sub-label) and five-cell rows (the regular/large head variants carry two extra label cells) — source rows carry differing non-empty cell counts (4/5), grid padded empty. Duplicated label cells carried verbatim.

Materials

  • The collected IFI 130 page prints geometry only — it carries no material, finish or load-rating rows, so those are confirmed per order rather than claimed from the table. Structural splitting rivets are typically quoted on body/mandrel material pairing (steel or aluminium body with steel mandrel) per the application; state the stack-up thicknesses, the head style (regular for standard bearing, large for thin/soft sheet) and the joint duty on the RFQ. Lead time, MOQ and price: contact for confirmation.

Ordering & documentation

Documents

Shipments of IFI 130 Structural Splitting Blind Rivets, Regular and Large Head (Self-Plugging, Pull Mandrel) are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for IFI 130 Structural Splitting Blind Rivets, Regular and Large Head (Self-Plugging, Pull Mandrel) orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.

Quotation

  • The product family (IFI 130 Structural Splitting Blind Rivets, Regular and Large Head (Self-Plugging, Pull Mandrel)), product standard/designation and drawing or part number.
  • The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
  • Material/grade, heat-treatment condition and surface finish, together with the service environment.
  • Quantity per size, delivery destination and required test or traceability documents.

Sample & supply

Minimum order quantity for ifi 130 structural splitting blind rivets, regular and large head (self-plugging, pull mandrel) is 10,000–50,000 pieces depending on size (applies to the standard sizes and finishes for ifi 130 structural splitting blind rivets, regular and large head (self-plugging, pull mandrel); mixed, special or custom variants are quoted — final commercial terms per quotation) Standard production for ifi 130 structural splitting blind rivets, regular and large head (self-plugging, pull mandrel) run 10–20 days. Quantities or variants of ifi 130 structural splitting blind rivets, regular and large head (self-plugging, pull mandrel) outside the standard range are confirmed at quotation.

Storage & shipping

IFI 130 Structural Splitting Blind Rivets, Regular and Large Head (Self-Plugging, Pull Mandrel) are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store ifi 130 structural splitting blind rivets, regular and large head (self-plugging, pull mandrel) dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.

Frequently asked questions

What makes a "structural splitting" blind rivet different from the ordinary break-pull open-end ones?

What the body does when the mandrel pulls. In an ordinary open-end rivet the body just buckles and clamps; in the splitting type the body is cut so it splits back along its length and spreads outward inside the hole — the set rivet fills the drilled hole instead of occupying it. That is the structural claim: more body contact, better resistance to pull-through and vibration in sheet metal. The cost is that the hole must be drilled to size (the split needs material to bite), and the two head styles here trade bearing diameter — the large head (0.775 in max at 1/4) exists for the thin or soft sheets where a regular head would pull through. If the drawing names IFI 130, the splitting behaviour is part of the call-out, not an option.

The grip row only says 1.000 in — how do I order longer rivets?

The collected table prints the minimum grip L1 (1.000 in for both 3/16 and 1/4); it does not tabulate the length ladder above it, so the longer grips are quoted against the actual stack-up rather than claimed from the table. Measure the total thickness of the joint including any gap, add the head style you want, and send both with the RFQ — we confirm the available grip range for the size and head style rather than quoting blind. Splitting rivets are especially grip-sensitive: a rivet set in too-thin a stack will not have split fully, and too-thick a stack leaves the body unseated, so the measured stack-up is the single most useful number on the enquiry.

What is the MOQ and lead time for IFI 130 Structural Splitting Blind Rivets, Regular and Large Head (Self-Plugging, Pull Mandrel)?

Orders under this designation have a minimum order quantity of 10,000–50,000 pieces depending on size. Standard production ships in 10–20 days. Final commercial terms are confirmed per quotation.

What should an RFQ for IFI 130 Structural Splitting Blind Rivets, Regular and Large Head (Self-Plugging, Pull Mandrel) state?

State the full designation (IFI 130 Structural Splitting Blind Rivets, Regular and Large Head (Self-Plugging, Pull Mandrel)), thread size and pitch or diameter, length or head dimension, finish, quantity per size, plus the destination country and any required certificate such as a mill test report per EN 10204 3.1; dimensions and schedule for this designation are confirmed with the quotation.

Request a Quote

Get factory-direct pricing from the manufacturer.

What to include in your IFI 130 Structural Splitting Blind Rivets, Regular and Large Head (Self-Plugging, Pull Mandrel) inquiry

  • ✓ Identify blind, solid or structural rivet type and the applicable product standard.
  • ✓ Give rivet-body diameter and grip range for the complete material stack, plus the prepared-hole size.
  • ✓ Specify head style/clearance and state body and mandrel materials separately for blind rivets.
  • ✓ For load-bearing joints, provide required rivet-specific tensile and shear values; do not substitute a bolt property class.
  • ✓ State finish, quantity, destination and any lot-test or traceability documents required.
  • ✓ Factory-direct pricing for your IFI 130 Structural Splitting Blind Rivets, Regular and Large Head (Self-Plugging, Pull Mandrel)
  • ✓ Standard and custom specifications
  • ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
  • ✓ Full fastener family support

We use your details only to answer this inquiry — see our Privacy notice for everything the form collects.