DIN 6887 Taper Keys with Gib Head

DIN 6887 gib-head taper keys — rectangular taper keys (1:100 taper) with a protruding gib head for removal, section b×h from 6×6 to 40×22, tabulated with h1 (head-to-face offset) and h2 (head height) per section.

Last updated: 2026-11

Request a Quote

DIN 6887 Taper Keys with Gib Head in an industrial setting
Illustrative image redrawn from real DIN 6887 Taper Keys with Gib Head product references — not a photograph of stocked items.

Specifications

A DIN 6887 key is a taper key — its underside rises 1 mm per 100 mm of length — driven into a tapered keyway until the hub is clamped tight with no clearance, in contrast to parallel (DIN 6885) keys that transmit torque through the sides of a clearance fit. The defining feature here is the gib head: a protruding hook beyond the keyway end that gives a wedge-pull surface so the key can be extracted where the shaft end is inaccessible — the reason this key shows up on flywheels, gear rims and pulleys mounted close to a shoulder or housing wall. The geometry chains three heights per section: h (key thickness at the tip end), h1 (the small offset at the gib-head end where the taper starts from the bearing face) and h2 (the gib head height itself). The collected grid covers ten printed sections from 6×6 up to 40×22. Reading notes before engineering use: the source grid does NOT tabulate the 20-28 sections — b 20, 22, 25 and 28 are absent from the ladder, which is exactly the band most machinery uses; a call in that band is a standard-document or quotation item on this page, not a tabulated dimension. The source page title itself prints "gip head" (sic) — carried as printed. Key length is a per-order dimension (the source prints no length ladder; lengths follow the standard's length series per section).

Standard / scope DIN 6887 taper keys with gib head — source title as printed: "Taper keys gip head" (sic)
Sections tabulated b×h: 6×6, 8×7, 10×8, 12×8, 14×9, 16×10, 18×11, 32×18, 36×20, 40×22 — ten printed sections; the 20-28 section band is NOT tabulated on the source page
Taper taper key (1:100 underside taper per the DIN 6887 form — the grid tabulates the section heights, the taper is the standard's fixed geometry)
Head heights (h1 / h2) h1 (tip-to-gib offset at the bearing face): 6,1 / 7,2 / 8,2 / 8,2 / 9,2 / 10,2 / 11,2 / 18,3 / 20,4 / 22,4; h2 (gib head height): 10 / 11 / 12 / 12 / 14 / 16 / 18 / 28 / 32 / 36 — decimal commas verbatim, duplicate adjacent h values (10×8 = 12×8 at 8,2) as printed
Not tabulated No length ladder, no material, no finish, no equivalents line printed on the source page — length is a per-order dimension from the standard's length series
Taper keys with gib head to DIN 6887 (source title: "Taper keys gip head" — sic)dimensions in mm; attribute legend per the source columns: b - key width, h - key thickness (tip end), h1 - head-end offset at the bearing face, h2 - gib head height
Attribute681012141618323640
b681012141618323640
h678891011182022
h16,17,28,28,29,210,211,218,320,422,4
h210111212141618283236
  • the size ladder prints b 6-18 then 32/36/40 — the 20-28 section band is absent from the source grid (not interpolated here; verify against the standard document).
  • duplicate adjacent h values (8 at both 10×8 and 12×8) and duplicate h1 (8,2 / 8,2) as printed.
  • the source page title prints "gip head" — the correct form is gib head; carried as printed and corrected in prose only.

Materials

  • The source page prints no makings line — no steel grade, no stainless option, no finish — so this page makes no material claim beyond the section grid. In trade practice DIN 6887 keys are supplied in steel (typically to the standard's default quality) with keyed-fit surface finish on the bearing faces, and stainless versions are quoted for corrosive duty, but both are quotation confirmations here. State the section (b×h), the effective length, the keyway form (taper keyway per the standard), material and any certificate requirement, and quantity per size.

Ordering & documentation

Documents

Shipments of DIN 6887 Taper Keys with Gib Head are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for DIN 6887 Taper Keys with Gib Head orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.

Quotation

  • The product family (DIN 6887 Taper Keys with Gib Head), product standard/designation and drawing or part number.
  • The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
  • Material/grade, heat-treatment condition and surface finish, together with the service environment.
  • Quantity per size, delivery destination and required test or traceability documents.

Sample & supply

Minimum order quantities and lead times for din 6887 taper keys with gib head are confirmed at quotation — send pin type, diameter, length and material on the RFQ and the quote will carry a firm schedule; sample availability is confirmed with the quotation.

Storage & shipping

DIN 6887 Taper Keys with Gib Head are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store din 6887 taper keys with gib head dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.

Frequently asked questions

Taper key (DIN 6887) or parallel key (DIN 6885) — when does the gib head earn its place?

Choose by hub removal, not by strength. A taper key wedges the hub onto the shaft with an interference-like clamp and zero play — good for reversing loads and impact, but removal means driving the key back out the way it came. The gib head is the answer where the key cannot be pushed out from behind: the protruding hook gives you a face to wedge against and pull the key. So DIN 6887 shows up on flywheels, gear rims and pulleys seated against shoulders. If the hub sits near a free shaft end and can be drawn off after loosening, a parallel DIN 6885 key is the simpler part. Watch axial overhang: the gib head projects beyond the hub face and needs running clearance — check it against rotating parts before you specify the length.

The grid stops at 18 and jumps to 32 — what about 20×12, 22×14, 25×16, 28×16?

The source page does not tabulate them, and this page does not extend the ladder from outside the source — the 20-28 band is exactly the most common machinery section range, so treat its absence as a data gap, not a product gap: those sections exist in the standard and are quoted as ordinary items. Verify the h/h1/h2 chain for the 20-28 sections against the standard document (or the quotation confirmation) rather than interpolating between the 18 and 32 columns — heights do not interpolate linearly.

What are h1 and h2 for, and why does the tip height differ from the head end?

Because the key is tapered. h is the section thickness at the tip (small) end; the underside rises 1:100 toward the gib-head end, so the bearing face at the head end sits h1 above the tip face line — h1 is effectively the taper rise plus fitting allowance, growing with section size (6,1 at 6×6 up to 22,4 at 40×22). h2 is the gib head height itself, roughly 2×h plus allowance (10 at 6×6 up to 36 at 40×22), sized so the hook withstands the wedge-pull without deforming. When machining a tapered keyway you cut to the h line and check the h1 offset at the mouth; when checking a delivered key, measure thickness at both ends — the difference over the working length is the taper proof.

What should an RFQ for DIN 6887 keys state?

Section b×h (from the tabulated ladder — or the 20-28 band as a quotation-confirmed item), effective length along the taper (length is not tabulated on the source page — it follows the standard's length series per section and your hub width), material and finish, certificate requirement if the assembly demands one, and quantity per size. State "gib head" explicitly so the supplier does not ship the plain taper key DIN 6881 — same taper, same sections, no head.

Request a Quote

Get factory-direct pricing from the manufacturer.

What to include in your DIN 6887 Taper Keys with Gib Head inquiry

  • ✓ Identify the pin type and its standard (for example parallel dowel or slotted spring pin).
  • ✓ Give nominal diameter, length and required fit/tolerance; include the mating-hole size and whether it is drilled or reamed.
  • ✓ State material, heat-treatment condition and corrosion finish, plus any specified shear or retention duty.
  • ✓ Give quantity per size, destination and inspection/certificate requirements.
  • ✓ Factory-direct pricing for your DIN 6887 Taper Keys with Gib Head
  • ✓ Standard and custom specifications
  • ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
  • ✓ Full fastener family support

We use your details only to answer this inquiry — see our Privacy notice for everything the form collects.