DIN 128A Spring Washers Type A (Curved)
DIN 128A spring washers Type A — the curved (bow) spring washer — sizes 2 to 36 with the full collected 20-size table across 7 block tables: bore d, outside diameter dc, section width b, material thickness s and loaded height h, plus the source's reference mass per 1000 units.
Last updated: 2026-11
Specifications
DIN 128A is the curved spring washer: a flat annular disc formed into a shallow bow, so it compresses elastically under the nut and keeps pressing after the joint settles. Unlike the split helical washer of DIN 127, nothing bites the bearing faces — the spring action is the whole mechanism, which suits plated or finished faces where edge bite would mar the surface, and gives a smoother, more predictable spring rate. The collected table runs sizes 2 to 36 in seven block tables, tabulating per size: the bore d with min/max limits, the outside diameter dc as a single max value, the section width b (Nominal / max / min), the material thickness s (Nominal / max / min) — the gauge of the disc doing the springing — and the loaded height h with min/max limits, the height left when the bow is pressed flat at full clamp. The source also prints a reference mass per 1000 units per size. The wave-formed counterpart is DIN 128B. Materials and finishes are not printed by the collected specification and stay per RFQ.
| Standard | DIN 128A — spring washers Type A, curved (bow) form; wave-formed counterpart DIN 128B |
|---|---|
| Series | 2 – 36 nominal diameter (20 sizes across 7 block tables) |
| Tabulated geometry | Per size: bore d (min / max), outside diameter dc max, section width b (Nominal / max / min), material thickness s (Nominal / max / min), loaded height h (min / max), reference mass per 1000 units ≈ kg |
| Dimensions at size 8 | d 8.1–8.5; dc max 14.8; b nominal 3 (max 3.15 / min 2.85); s nominal 1.6 (max 1.7 / min 1.5); h 2.45–2.75; weight 1.3 kg/1000 |
| Dimensions at size 16 | d 16.2–17; dc max 27.4; b nominal 5 (max 5.2 / min 4.8); s nominal 2.8 (max 2.95 / min 2.65); h 4.5–5.1; weight 7 kg/1000 |
| Dimensions at size 36 | d 36.5–37.7; dc max 58.2; b nominal 10 (max 10.25 / min 9.75); s nominal 6 (max 6.2 / min 5.8); h 10.3–11.3; weight 68 kg/1000 |
| Materials / strength | Not tabulated by the collected specification — per RFQ (spring material and finish per drawing callout) |
Materials
- Material and finish specified per RFQ — the collected specification table covers geometry and reference mass only
Ordering & documentation
Documents
Shipments of DIN 128A Spring Washers Type A (Curved) are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for DIN 128A Spring Washers Type A (Curved) orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.
Quotation
- The product family (DIN 128A Spring Washers Type A (Curved)), product standard/designation and drawing or part number.
- The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
- Material/grade, heat-treatment condition and surface finish, together with the service environment.
- Quantity per size, delivery destination and required test or traceability documents.
Sample & supply
Supply source for DIN 128A Spring Washers Type A (Curved): own manufacturing plus qualified outsourcing (per the owner-confirmed scope of supply (own production plus outsourcing)).
Minimum order quantity for din 128a spring washers type a (curved) is 10,000 pieces (applies to the standard sizes and finishes for din 128a spring washers type a (curved); mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for din 128a spring washers type a (curved) run 3–7 days. Quantities or variants of din 128a spring washers type a (curved) outside the standard range are confirmed at quotation.
Storage & shipping
DIN 128A Spring Washers Type A (Curved) are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store din 128a spring washers type a (curved) dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.
Frequently asked questions
Curved DIN 128A or split DIN 127B — what does the form change?
The locking surface. The DIN 127B split ring locks partly by its edges biting into the nut and joint faces — effective, but it marks the surfaces and its bite depends on installation. The DIN 128A curved disc has no split and no edges: it locks by elastic spring force alone, pressing the nut against the thread even as the joint creeps, and it leaves bearing faces unmarked. That makes Type A the choice under finished, plated or soft faces, and where a defined, repeatable spring rate matters more than edge bite. On the size ladder the two series align closely at the common sizes, so swapping the form usually changes only the locking behaviour, not the stack height — verify against the h/H columns of the respective tables.
What does the s column tell me about the spring?
It is the gauge of the disc doing the springing — the collected table shows it growing from 0.5 mm at size 2 to 6 mm at size 36, tracking the b width at roughly half its value. A thicker s means a stiffer, higher-load spring stroke; a thinner s gives a softer, longer-travel cushion for joints that settle a lot. Since the collected table prints s with real tolerance bands (for example 1.5–1.7 mm at size 8), production can hold the spring rate on incoming inspection; if your joint depends on a specific compression curve, state the thickness band at quotation rather than assuming nominal.
What is the MOQ and lead time for this washer type?
Minimum order quantity is 1,000 pieces per item. Standard samples ship in 3–5 days, bulk standard parts in 15–25 days, and custom OEM parts in 30–45 days. Common sizes are widely stocked; confirm the exact schedule against quantity and size mix at quotation.
Request a Quote
Get factory-direct pricing from the manufacturer.
What to include in your DIN 128A Spring Washers Type A (Curved) inquiry
- ✓ Identify the washer form and dimensional standard (for example flat, fender, spring-lock or hardened structural washer).
- ✓ Give the mating bolt size plus inside diameter, outside diameter and thickness; include the applicable dimensional series.
- ✓ State washer material and any specified hardness class or coating. Washer hardness is not a bolt property class.
- ✓ Describe the bearing surface or locking function, quantity per size and destination.
- ✓ Factory-direct pricing for your DIN 128A Spring Washers Type A (Curved)
- ✓ Standard and custom specifications
- ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
- ✓ Full fastener family support