DIN 3570 U-Bolts (NW 23 – 332)
DIN 3570 U-bolts, NW 23 to 332 — round-bend U straps keyed by pipe diameter, with the matching thread (M10 to M20), inner gap D1, minimum thread length B1, leg height H1 and pitch E tabulated per pipe size; steel st37 per the collected panel.
Last updated: 2026-11
Specifications
DIN 3570 is the standard U-bolt for clamping a pipe to a support: a round-bent strap whose two threaded legs reach around the pipe and through the flange or bracket, held by nuts on both legs. What makes the collected table immediately usable is its indexing — the ladder runs by NW pipe diameter (the legend prints "NW - diameter pipe") from NW 23 up to NW 332, and for each pipe size it prints the matching thread D3 (M10 for the small pipes, stepping to M12, then M16 at NW 120, then M20 from NW 228), the shank diameter D2 (10 to 20), the inner gap D1 — printed as a range where the pipe's outer diameter plus clearance needs it, e.g. "108 - 114,3" at NW 120 — the pitch E (legend: "e - pitch"; 33 up to 352), the leg height H1 inside the bend (60 up to 385), and the minimum thread length B1 ("at least", 30 up to 70). The Makings panel lists steel st37 only; stainless, plastic and non-ferrous print "-" and are not claimed — the source's own inquiry ledger, however, shows live demand for A2/A4 stainless and long-leg 1.4571 variants, so a stainless or long-leg requirement is stated on the RFQ and quoted, not assumed from the table. For the inch-series pipe-size chart, the registered IFI-136 U-bolt page is the complementary, non-metric reference.
| Standard / scope | DIN 3570 U-bolts (source title "DIN 3570 - U-bolts"), size ladder NW 23 to NW 332 keyed by pipe diameter: 23, 30, 38, 46, 52, 64, 82, 94, 120, 148, 176, 228, 282, 332; no equivalent norm printed by the source |
|---|---|
| Pipe fit (D1, inner gap) | D1 20 - 21 at NW 23 → 318 - 323,9 at NW 332; printed as a range where pipe OD plus clearance demands it (single value where the fit is fixed, e.g. 76,1 at NW 82, 88,9 at NW 94) |
| Thread / shank (D3, D2) | D3 M10 (NW 23-52) → M12 (NW 64-94) → M16 (NW 120-176) → M20 (NW 228-332); D2 shank 10 → 20 |
| Legs (E, H1) | E pitch between legs 33 → 352; H1 leg height inside the bend 60 → 385 |
| Thread length (B1) | B1 "length of the thread (at least)" 30 (NW 23) → 70 (NW 228-332) |
| Materials | Steel st37 per the source Makings panel (stainless, plastic and non-ferrous print "-" — not claimed); the source's own inquiry ledger shows live A2/A4 and 1.4571 stainless demand — quoted per RFQ |
| Not tabulated | No mass row, no finishes, no long-leg/special-bend variants — confirmed at quotation (tenant supply range) |
| NW (Size) | 23 | 30 | 38 | 46 | 52 |
|---|---|---|---|---|---|
| D1 (a, inner diameter) | 20 - 21 | 25 - 26,9 | 30 - 33,7 | 38 - 42,4 | 44,5 - 48,3 |
| B1 (b, length of the thread, at least) | 30 | 40 | 40 | 50 | 50 |
| D2 (d2, diameter of the screw shank) | 10 | 10 | 10 | 10 | 10 |
| D3 (d3, nominal diameter of the thread) | M10 | M10 | M10 | M10 | M10 |
| E (e, pitch) | 33 | 40 | 48 | 56 | 62 |
| H1 (h, height) | 60 | 70 | 76 | 86 | 92 |
- The source legend letters (b, h, d3, e, d2, NW, a) do not match the table row labels (D1, B1, D2, D3, E, H1); the bracketed legend readings are a best-fit mapping and are flagged, not adjudicated.
- The header row is keyed by NW pipe diameter despite the bare header word "Size" (legend: "NW - diameter pipe").
| NW (Size) | 64 | 82 | 94 | 120 | 148 |
|---|---|---|---|---|---|
| D1 (a, inner diameter) | 57 - 60,3 | 76,1 | 88,9 | 108 - 114,3 | 133 - 139,7 |
| B1 (b, length of the thread, at least) | 50 | 50 | 50 | 60 | 60 |
| D2 (d2, diameter of the screw shank) | 12 | 12 | 12 | 16 | 16 |
| D3 (d3, nominal diameter of the thread) | M12 | M12 | M12 | M16 | M16 |
| E (e, pitch) | 76 | 94 | 106 | 136 | 164 |
| H1 (h, height) | 109 | 125 | 138 | 171 | 191 |
| NW (Size) | 176 | 228 | 282 | 332 |
|---|---|---|---|---|
| D1 (a, inner diameter) | 159 - 168,3 | 216 - 219,1 | 267 - 273 | 318 - 323,9 |
| B1 (b, length of the thread, at least) | 60 | 70 | 70 | 70 |
| D2 (d2, diameter of the screw shank) | 16 | 20 | 20 | 20 |
| D3 (d3, nominal diameter of the thread) | M16 | M20 | M20 | M20 |
| E (e, pitch) | 192 | 248 | 302 | 352 |
| H1 (h, height) | 217 | 283 | 334 | 385 |
- The source grid prints a fifth, empty column slot in this block; every row ends with the same empty cell — carried as a uniform truncation, not a missing value.
Materials
- Steel st37 per the collected source's Makings panel — the plain-carbon workhorse for pipe clamping in dry or coated service; stainless (A2/A4, or 1.4571 for the long-leg variants seen in live RFQ traffic) is not tabulated by the source, so it is confirmed at quotation rather than claimed; sizes outside the NW 23-332 ladder and non-standard bends per RFQ
Ordering & documentation
Documents
Shipments of DIN 3570 U-Bolts (NW 23 – 332) are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for DIN 3570 U-Bolts (NW 23 – 332) orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.
Quotation
- The product family (DIN 3570 U-Bolts (NW 23 – 332)), product standard/designation and drawing or part number.
- The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
- Material/grade, heat-treatment condition and surface finish, together with the service environment.
- Quantity per size, delivery destination and required test or traceability documents.
Sample & supply
Supply source for DIN 3570 U-Bolts (NW 23 – 332): own manufacturing plus qualified outsourcing (per the owner-confirmed scope of supply (own production plus outsourcing)).
Minimum order quantity for din 3570 u-bolts (nw 23 – 332) is 1,000–10,000 pieces depending on size (applies to the standard sizes and finishes for din 3570 u-bolts (nw 23 – 332); mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for din 3570 u-bolts (nw 23 – 332) run 3–7 days. High-strength and custom parts for din 3570 u-bolts (nw 23 – 332) run 15–25 days. Quantities or variants of din 3570 u-bolts (nw 23 – 332) outside the standard range are confirmed at quotation.
Storage & shipping
DIN 3570 U-Bolts (NW 23 – 332) are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store din 3570 u-bolts (nw 23 – 332) dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.
Frequently asked questions
How do I read the DIN 3570 table for my pipe?
Start from your pipe's nominal diameter (NW/DN), not the thread: the ladder is keyed by pipe size, and each row tells you what the U-bolt looks like for that pipe. D1 is the inner gap between the legs — check your pipe's actual outer diameter fits inside the printed range (e.g. at NW 120 the gap prints "108 - 114,3", which accepts a 108 mm pipe up to 114,3 mm). D3 gives the matching thread your nut takes (M10 up to M20 as the pipes grow), D2 the shank diameter, E the pitch (the legend's own word — read it against the hole spacing your support plate needs), H1 the leg height inside the bend (how much reach past the pipe you have for the nut), and B1 the minimum thread length. One boundary: the legend that accompanies the table uses different letters (b, h, d3, e, d2, NW, a) than the table rows (D1, B1, D2, D3, E, H1) — the source prints the mismatch itself; the pairing used here is the best-fit reading and is flagged rather than adjudicated, so where a drawing demands an exact letter mapping, confirm it against the manufacturer drawing at quotation.
What does an RFQ for DIN 3570 U-bolts need to state?
The pipe size (NW/DN) first — that alone fixes D1, D3, D2, E, H1 and B1 from the table — then the deviations: pipe OD if it sits at the edge of the printed D1 range, stainless or long legs if your service needs them (the source tabulates steel st37 only and prints "-" for stainless, so stainless is a quotation item, and the source's own inquiry ledger shows exactly these variants being sourced live: A2, A4, long-leg 1.4571), the support-plate thickness that sets how much thread you actually need beyond the B1 minimum, and the finish or coating (the source tabulates none). Non-standard bends, longer legs and sizes outside the NW 23-332 ladder are quoted to drawing.
DIN 3570 or the inch-series U-bolt chart — which applies to my project?
They are complementary references, not rivals: DIN 3570 is the metric standard whose ladder runs by NW pipe diameter from 23 to 332 with matching M10-M20 threads — the natural spec for metric piping and European plant work. The registered IFI-136 U-bolt page tabulates the inch-series pipe chart (1/2 to 36 in pipe, 1/4 to 1 in bolt diameter) used in US-style piping. Pick the one your project's piping spec invokes; where a plant mixes both, match the U-bolt standard to the flange and support hardware already specified, because the hole spacing (E) and thread must line up with the mating plate. Sizes and fittings that fall between the two ladders are quoted per RFQ.
Related knowledge
- What Bolt Property Classes 8.8, 10.9 and 12.9 Encode — and When High Strength Stops Being the Right Choice
- Bolt Grade Selection: ISO 898-1 8.8/10.9/12.9 vs ASTM A307 and A325
- 8.8 vs 10.9 vs 12.9 Bolts: Strength, Hardness and Cost — What the Evidence Settles
- Calculating Bolt Preload and Clamp Force: Torque, Friction and Tightening Method
- How to Determine Tightening Torque and Choose a Tightening Method for a Bolted Joint
- Fastener Failure Modes: Which Fatigue, Creep and SCC Controls the Evidence Supports
- Hydrogen Embrittlement in High-Strength Bolts: Which Grades Need Controls, Which Coatings and Baking Schedules Are Acceptable, and What to Require Before the RFQ
Request a Quote
Get factory-direct pricing from the manufacturer.
What to include in your DIN 3570 U-Bolts (NW 23 – 332) inquiry
- ✓ Name the bolt standard and product form, then give nominal diameter, pitch, length and threaded length.
- ✓ State the applicable property class or material grade, head style, and coating or finish.
- ✓ Identify the mating nut/washer and the joint duty; include any specified preload, tightening method or friction condition.
- ✓ Give quantity per size, destination and required material or inspection certificates.
- ✓ Factory-direct pricing for your DIN 3570 U-Bolts (NW 23 – 332)
- ✓ Standard and custom specifications
- ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
- ✓ Full fastener family support