DIN 797 Special Foundation Bolts (M24 – M100)
DIN 797 special foundation bolts — cast-in foundation anchors with an internal thread d3 (M12/M16/M20) in the ejector end, tabulated over M24 to M100 with thread lengths b1/b2 (75-260), shank d2 (34-80), hole depth t (22-33) and ejector length z2 (14-56), steel 3.6 with 8g thread as printed.
Last updated: 2026-11
Specifications
DIN 797 is not a machine bolt: it is a foundation bolt for casting into concrete, and its defining feature is at the far end — the source legend gives d3 as "the nominal diameter of the thread" and z2 as "the length of the ejector", describing an internally threaded anchor end where the machine to be seated is threaded down onto the cast-in bolt (the ejector length z2 being the lead-in section the setting equipment grips). The series is heavy: the printed ladder runs M24 to M100, and everything about the print says mass concrete work — thread lengths b1/b2 of 75 to 260 mm ("at least", per the legend, so embedding geometry is sized before final machining), a smooth shank d2 of 34 to 80, and t, the minimum depth of the hole the bolt seats in. The source legend also defines l (length of bolt) but tabulates no length row — overall length is a per-foundation dimension agreed from the embedding drawing, not a table pick. The grid itself is ragged as printed: the d2 row stops at M80 and the d3/t rows stop at M90 against the full M100 ladder — transcribed verbatim and flagged here, not padded. Property class as printed: steel 3.6 only, thread tolerance 8g; this is anchoring hardware where the concrete carries the load and the bolt geometry positions it, not a high-strength structural bolt. Pair the nut side with DIN 798, the special foundation square nut registered alongside this page. Equivalent norm as printed: PN 85061.
| Standard / scope | DIN 797 special foundation bolts (cast-in foundation anchors with internally threaded / ejector end per the source legend) |
|---|---|
| Size ladder (d1) | M24, M30, M36, M42, M48, M56, M64, M72, M80, M90, M100 — eleven printed sizes |
| Thread lengths (b1 / b2, "at least") | b1: 75 / 85 / 95 / 105 / 120 / 140 / 155 / 170 / 185 / 205 / 225; b2: 110 / 120 / 140 / 150 / 160 / 170 / 190 / 200 / 220 / 240 / 260 (M24 → M100) |
| Shank (d2) / hole depth (t) | d2: 34 / 38 / 45 / 50 / 55 / 65 / 70 / 80 (printed to M80 only); t: 22 / 22 / 22 / 26 / 26 / 26 / 33 / 33 / 33 (printed to M90 only) — ragged rows as captured |
| Internal thread (d3) / ejector (z2) | d3: M12 (M24-M36), M16 (M42-M48), M20 (M56-M90 as printed); z2: 14 / 18 / 22 / 25 / 28 / 32 / 36 / 40 / 45 / 50 / 56 |
| Materials / thread (as printed) | Steel: 3.6; Thread: 8g; Stainless: -; Plastic: -; Non Ferrous: - (source makings block verbatim) |
| Equivalents (as printed) | Equivalent norms: PN 85061 |
| Not tabulated | The legend defines l (length of bolt) but the grid prints no length row — overall length follows the foundation embedding drawing and is a per-order RFQ dimension |
| row | M24 | M30 | M36 | M42 | M48 | M56 | M64 | M72 | M80 | M90 | M100 |
|---|---|---|---|---|---|---|---|---|---|---|---|
| d1 | M24 | M30 | M36 | M42 | M48 | M56 | M64 | M72 | M80 | M90 | M100 |
| b1 | 75 | 85 | 95 | 105 | 120 | 140 | 155 | 170 | 185 | 205 | 225 |
| b2 | 110 | 120 | 140 | 150 | 160 | 170 | 190 | 200 | 220 | 240 | 260 |
| d2 | 34 | 38 | 45 | 50 | 55 | 65 | 70 | 80 | |||
| d3 | M12 | M12 | M12 | M16 | M16 | M20 | M20 | M20 | M20 | ||
| t | 22 | 22 | 22 | 26 | 26 | 26 | 33 | 33 | 33 | ||
| z2 | 14 | 18 | 22 | 25 | 28 | 32 | 36 | 40 | 45 | 50 | 56 |
- Row 4 (d2): the d2 row prints 8 cells — it stops at M80 against the 11-size ladder, as captured (not padded).
- Row 6 (t): the d3 and t rows print 9 cells — they stop at M90 against the 11-size ladder, as captured (not padded).
- the legend defines l (length of bolt) but the grid prints no length row — overall length is a per-foundation drawing dimension, not a table pick.
- the source prints no finish line — the makings block (Steel: 3.6, Thread: 8g) is the page's only material authority.
Materials
- The source makings block prints Steel: 3.6 with Thread: 8g and a literal "-" for Stainless, Plastic and Non Ferrous — one low property class, which is consistent with the part's duty: a foundation bolt cast into concrete is sized by its embedding geometry (b1/b2 thread lengths, t hole depth, the d2 shank) and the concrete, not by bolt steel strength, so upgrading the class is not a like-for-like improvement and any deviation is an engineering decision, not a purchase option. Coating (these are near-universally galvanized or otherwise corrosion-protected for buried service) is a quotation confirmation — the source prints no finish. State d1, overall length from the embedding drawing, d3 and z2 explicitly (the mating machine threads onto them), class, coating, any foundation acceptance test, and quantity per size; retrofit work should measure the failed bolt's d2 and z2 before ordering — a replaced foundation bolt that does not match the ejector interface will not accept the machine seating.
Ordering & documentation
Documents
Shipments of DIN 797 Special Foundation Bolts (M24 – M100) are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for DIN 797 Special Foundation Bolts (M24 – M100) orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.
Quotation
- The product family (DIN 797 Special Foundation Bolts (M24 – M100)), product standard/designation and drawing or part number.
- The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
- Material/grade, heat-treatment condition and surface finish, together with the service environment.
- Quantity per size, delivery destination and required test or traceability documents.
Sample & supply
Supply source for DIN 797 Special Foundation Bolts (M24 – M100): own manufacturing plus qualified outsourcing (per the owner-confirmed scope of supply (own production plus outsourcing)).
Minimum order quantity for din 797 special foundation bolts (m24 – m100) is 1,000–10,000 pieces depending on size (applies to the standard sizes and finishes for din 797 special foundation bolts (m24 – m100); mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for din 797 special foundation bolts (m24 – m100) run 3–7 days. High-strength and custom parts for din 797 special foundation bolts (m24 – m100) run 15–25 days. Quantities or variants of din 797 special foundation bolts (m24 – m100) outside the standard range are confirmed at quotation.
Storage & shipping
DIN 797 Special Foundation Bolts (M24 – M100) are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store din 797 special foundation bolts (m24 – m100) dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.
Frequently asked questions
How is a DIN 797 foundation bolt different from an ordinary anchor bolt or a DIN 529 masonry bolt?
The interface is the difference. Ordinary foundation and masonry bolts present an external thread for a nut on top of the concrete; DIN 797 presents an internally threaded end (d3 M12/M16/M20 per the printed rows) with an ejector lead-in z2 — the bolt is cast in, and the machine or frame is threaded down onto it, so the visible fastening is a screw-into-bolt joint rather than a nut-on-stud joint. That changes what you order and inspect: the mating dimensions are d3 and z2, not the top-thread length alone, and the printed b1/b2 "at least" thread lengths exist so the cast-in bolt can be cut or machined to the embedding drawing without losing thread engagement. Where the design actually calls for a nut-on-stud anchor, that is a different standard — match the drawing, not the family name.
The d2, d3 and t rows stop before M100 — does that mean those sizes do not exist?
It means the source grid prints them shorter, as captured: the d2 row stops at M80 and the d3/t rows stop at M90 while b1/b2/z2 run the full M24-M100 ladder. This page transcribes the rows verbatim and flags the ragged print rather than extending values from the standard document, because inventing the missing cells would put uncollected numbers on the page. Practical read: for M80 and below the grid is complete; for the largest ladders (M90/M100) the shank diameter, internal thread and hole depth are quotation-confirmations against the standard document. If your foundation design uses those top sizes, treat the standard text as the dimension authority for the rows the source does not print.
What should an RFQ for DIN 797 foundation bolts state?
Thread size d1 (M24-M100 from the ladder), overall bolt length from the embedding drawing (the source legend defines l but prints no ladder), the internal thread d3 and ejector length z2 as explicit mating dimensions, property class (3.6 as printed), coating (galvanizing for buried service is a quotation confirmation — the source prints none), any embedding or pull-out acceptance requirement, and quantity per size. For machine-reseat retrofits, measure the removed bolt's d3 and z2 and state them as measured — the internal-thread interface is where a mismatched replacement fails, and it is invisible until the machine is lowered onto the bolt.
Related knowledge
- What Bolt Property Classes 8.8, 10.9 and 12.9 Encode — and When High Strength Stops Being the Right Choice
- Bolt Grade Selection: ISO 898-1 8.8/10.9/12.9 vs ASTM A307 and A325
- 8.8 vs 10.9 vs 12.9 Bolts: Strength, Hardness and Cost — What the Evidence Settles
- Calculating Bolt Preload and Clamp Force: Torque, Friction and Tightening Method
- How to Determine Tightening Torque and Choose a Tightening Method for a Bolted Joint
- Fastener Failure Modes: Which Fatigue, Creep and SCC Controls the Evidence Supports
- Hydrogen Embrittlement in High-Strength Bolts: Which Grades Need Controls, Which Coatings and Baking Schedules Are Acceptable, and What to Require Before the RFQ
Request a Quote
Get factory-direct pricing from the manufacturer.
What to include in your DIN 797 Special Foundation Bolts (M24 – M100) inquiry
- ✓ Name the bolt standard and product form, then give nominal diameter, pitch, length and threaded length.
- ✓ State the applicable property class or material grade, head style, and coating or finish.
- ✓ Identify the mating nut/washer and the joint duty; include any specified preload, tightening method or friction condition.
- ✓ Give quantity per size, destination and required material or inspection certificates.
- ✓ Factory-direct pricing for your DIN 797 Special Foundation Bolts (M24 – M100)
- ✓ Standard and custom specifications
- ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
- ✓ Full fastener family support