DIN 547 Two-Hole Nuts (M2 – M10)

DIN 547 two-hole nuts — flat, low-profile nuts with two counterbored holes for a two-pin (hook) spanner, M2 to M10 with fine-to-coarse pitches P 0,4 to 1,5, for clamping where a hexagon cannot be gripped: tooling, machine controls, optical and instrument assemblies.

Last updated: 2026-11

Request a Quote

DIN 547 Two-Hole Nuts (M2 – M10) in an industrial setting
Illustrative image redrawn from real DIN 547 Two-Hole Nuts (M2 – M10) product references — not a photograph of stocked items.

Specifications

A DIN 547 two-hole nut is what you reach for when the clamp has to be flat and the drive has to stay off the part: a thin rectangular-ish flat nut whose two counterbored holes take the pins of a two-pin spanner (the hook-faced wrench machinists call a "Spanner" or DIN-547 key). That drive geometry is the point — no hex corners to round, no protruding heads, and the clamping face stays clear across its full diameter — which is why the designation shows up on machine-tool controls, jigs, optical benches and instrument covers more than on any structural job. The collected ladder runs M2 to M10 (the parenthesized "(M3,5)" carried as the source prints it — the non-preferred size), pitch P 0,4 to 1,5, nut height m just 2 to 8 — roughly half a hex nut or less — with hole spacing e Nominal 4 to 15 and the da row ("Turning diameter shrinkage", the source's own wording) giving the safe spanner swing clearance. Materials per the Makings panel: steel and stainless A1, thread tolerance 6H. Two reading notes before engineering use: the t (hole depth) row prints values only from M4 up — at M2/M3 the source carries a merged "tdrough holes" cell (sic) instead — and the e row prints min. values larger than its max. values at every thread, carried verbatim and flagged; see the FAQs.

Standard / scope DIN 547 two-hole nuts (source title "DIN 547 - Two-hole nuts"; "Current norm: DIN 547", "Equivalent norms: PN 82464" as printed), thread sizes M2 to M10 incl. the non-preferred "(M3,5)"
Pitch (P) 0,4 (M2), 0,45 (M2,5), 0,5 (M3), 0,6 (M3,5), 0,7 (M4), 0,8 (M5), 1 (M6), 1,25 (M8), 1,5 (M10); thread tolerance 6H per the Makings panel
Nut height (m) nominal = max. 2 (M2) to 8 (M10), min. 1,75 to 7,64 — roughly half the height of a comparable hex nut
Hole spacing (e) Nominal 4 to 15 (M2 to M10) per the source legend "e - spacing of holes"; the e min./max. rows print min. larger than max. at every thread (e.g. 4,15/3,85 at M2) — carried verbatim, flagged
Nut diameter (dk) nominal = max. 5,5 (M2) to 22 (M10), min. 5,2 to 21,48; da ("Turning diameter shrinkage") min. 0,2 at M2 to 10 at M10, max. 2,3 to 10,8
Hole / depth (dh, t) dh hole diameter nominal = min. 1 to 3,5 (max. 1,14 to 3,68); t hole depth printed only M4-M10 (min. 1,3 to 3,8; max. 1,7 to 4,3) — at M2/M3 the source carries the merged "tdrough holes" cell instead of values
Weight 0,31 (M2) to 19,3 (M10) kg per 1000 pieces per the source's own header row
Materials Steel; stainless A1 per the source Makings panel; plastic and non-ferrous print "-" — not claimed
Not tabulated No torque or preload ratings, no finishes, no hardened variants — confirmed at quotation
Two-hole nuts to DIN 547dimensions in mm (the source's own table header); weight row is kg per 1000 pieces per its own header
AttributeLimitM2M2,5M3(M3,5)M4M5M6M8M10
AttributeLimitM2M2,5M3(M3,5)M4M5M6M8M10
P0,40,450,50,60,70,811,251,5
damin.0,22,533,5456810
max.2,32,93,544,65,756,758,7510,8
dhnominal = min.11,21,51,51,522,533,5
max.1,141,341,641,641,642,142,643,143,68
dknominal = max.5,57891012141822
min.5,26,647,648,649,6411,5713,5717,5721,48
eNominal455,5678101315
min.4,155,155,656,157,188,1810,1813,1815,18
max.3,854,855,355,856,827,829,8212,8214,82
mnominal = max.22,22,533,54,256,58
min.1,751,952,252,753,23,94,76,147,64
tmin.tdrough holes1,31,81,82,32,83,33,8
max.1,72,22,22,73,23,84,3
Weight kg/1000pcs0,310,560,831,261,833,084,9310,519,3
  • Row 13 (): "tdrough holes" (sic — the source's spelling) is a merged cell covering the M2 and M3 columns across both t sub-rows; t prints values only from M4 to M10, so no hole depth is tabulated at M2/M3 — verify against the standard document before drilling.
  • Row 10 (): the e row prints min. values larger than its max. values (M2: min. 4,15 vs max. 3,85 — inverted at every thread) — both rows carried verbatim as printed, not swapped.
  • legend spellings are the source's own ("da - Turning diameter shrinkage", "e - spacing of holes"); the weight row has no legend entry (unit read from its own header).

Materials

  • The source tabulates steel and stainless A1 (thread tolerance 6H). Steel is the tooling-and-jig workhorse; A1 stainless covers instrument and food-line builds where the low profile sits in wash-down areas. The counterbored holes are the wear point in service — a soft nut rounds its pin seats and the spanner skips — so re-torquing duty favors buying spare nuts rather than hardened claims the source does not make. Finishes print "-" and are quotation items; on an adjustable clamp that is re-torqued periodically, plain steel with a light oil film is the honest default and zinc or black oxide are specified per build.

Ordering & documentation

Documents

Shipments of DIN 547 Two-Hole Nuts (M2 – M10) are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for DIN 547 Two-Hole Nuts (M2 – M10) orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.

Quotation

  • The product family (DIN 547 Two-Hole Nuts (M2 – M10)), product standard/designation and drawing or part number.
  • The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
  • Material/grade, heat-treatment condition and surface finish, together with the service environment.
  • Quantity per size, delivery destination and required test or traceability documents.

Sample & supply

Supply source for DIN 547 Two-Hole Nuts (M2 – M10): own manufacturing plus qualified outsourcing (per the owner-confirmed scope of supply (own production plus outsourcing)).

Minimum order quantity for din 547 two-hole nuts (m2 – m10) is 10,000 pieces (applies to the standard sizes and finishes for din 547 two-hole nuts (m2 – m10); mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for din 547 two-hole nuts (m2 – m10) run 3–7 days. Quantities or variants of din 547 two-hole nuts (m2 – m10) outside the standard range are confirmed at quotation.

Storage & shipping

DIN 547 Two-Hole Nuts (M2 – M10) are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store din 547 two-hole nuts (m2 – m10) dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.

Frequently asked questions

The table has no hole depth (t) at M2 and M3 — what does "tdrough holes" mean?

In the source grid, the M2 and M3 columns of the t rows are occupied by a merged cell reading "tdrough holes" (the source's own spelling, evidently "through holes"), spanning both sizes across the min. and max. sub-rows — it is a note, not a dimension. The plain reading: at M2 and M3 the two holes are drilled through the nut's full (thin) height, so no tabulated min./max. depth band exists; from M4 up, t prints a real band (M4: min. 1,3 / max. 1,7, rising to min. 3,8 / max. 4,3 at M10). This page carries the cell verbatim rather than inventing depth numbers. Practical consequence: an M2/M3 nut's pin engagement is whatever the 2-2,5 mm height gives, and spanner pin length should be chosen accordingly; if a drawing needs a tabulated depth band at M2 or M3, confirm it against the standard document.

The e row prints min. values bigger than its max. values — is that a transcription error?

No — it is exactly what the source prints, at every thread: e Nominal 4 at M2 with min. 4,15 and max. 3,85, and the same inversion (min. above max.) down the row to M10 (15 / 15,18 / 14,82). This page transcribes both rows verbatim and flags them rather than swapping them. The likely reading is direction-of-measurement: "min." and "max." here plausibly refer to a clearance envelope (hole-to-edge material or the spanner swing), not the spacing tolerance itself, since the Nominal value 4 sits between the two prints and the legend calls e "spacing of holes" in the source's own wording. Either way, the design-limiting number for spanner pin layout is the Nominal row; do not use the inverted min./max. pair for a tolerance stack without checking the standard document first.

DIN 547 two-hole nut or DIN 1804 slotted round nut — which does my assembly need?

The drive tells you. DIN 1804 is a round nut with miller slots on its face — it needs a hook spanner reaching into a slot, runs on threaded shafts and bearing lock duty, and its cylindrical body can rotate inside a counterbore only when locked separately. DIN 547 is flat and square-ish with two counterbored holes — it needs a two-pin spanner, sits flush in a recess or on a flat face, and its full rectangular face resists rotation by contact, not by a separate lock. Choose DIN 547 when the nut must present a flat clamping face in a shallow recess (machine controls, jigs, optical fixtures) and the drive can be two pins; choose DIN 1804 when the part is a shaft-end lock. Both share the "thin, spanner-driven, precision" role — they are not interchangeable because the pin spacing (e) and the slot geometry never match.

What should an RFQ for DIN 547 two-hole nuts state?

Thread size with pitch (M6 x 1 style — the ladder mixes fine and coarse pitches, and the non-preferred (M3,5) is parenthesized for a reason), material (steel or A1 stainless per the tabulated lines), the mating spanner's pin diameter and spacing if it is an existing tool (so e and dh are matched to your wrench, not assumed), finish if not plain, quantity per size — and, if your fixture needs it, the note that hole depth t at M2/M3 is through-drilled per the source. Anything outside the table — hardened nuts, sizes past M10, or a tabulated t band at M2/M3 — is confirmed at quotation against the standard document.

Request a Quote

Get factory-direct pricing from the manufacturer.

What to include in your DIN 547 Two-Hole Nuts (M2 – M10) inquiry

  • ✓ Name the nut standard, style and nominal thread size/pitch, including metric or inch thread series.
  • ✓ State the nut property class or material and the bolt class/material it must be paired with.
  • ✓ Specify locking or prevailing-torque feature, coating and corrosion environment.
  • ✓ Give quantity per size, destination and any lot or mechanical-test documentation.
  • ✓ Factory-direct pricing for your DIN 547 Two-Hole Nuts (M2 – M10)
  • ✓ Standard and custom specifications
  • ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
  • ✓ Full fastener family support

We use your details only to answer this inquiry — see our Privacy notice for everything the form collects.