Heavy Hex Slotted Nuts (Inch Series)

Heavy hex slotted nuts, inch series, 1/4 to 1 1/2 in nominal — the thick-section slotted hex nut with heavy-series width across flats, tabulated with the full F/G/H/T/S dimension bands per size as printed by the source.

Last updated: 2026-11

Request a Quote

Heavy Hex Slotted Nuts (Inch Series) in an industrial setting
Illustrative image redrawn from real Heavy Hex Slotted Nuts (Inch Series) product references — not a photograph of stocked items.

Specifications

Heavy hex slotted nuts combine two upgrades over the plain hex slotted nut: the heavy-series width across flats (more wrench bearing area and a thicker, stronger nut body) and castellations for a cotter or slotted spring pin to lock the nut against rotation. The slot runs across the full top face, so after torquing you align the nearest slot with the pinned hole and insert the pin — which is why these nuts appear on rotating equipment, linkages and any joint where loss of clamp by vibration is unacceptable and a prevailing-torque insert is not wanted. Against the plain hex slotted nut (the same calculator's default series), the heavy version steps the flats up — 1/2 in basic at 1/4 nominal versus 7/16 for plain — while thickness runs close to the heavy hex nut standard. The table carries the whole printed band per size: basic fractions for F, H and the max/min decimals behind them, plus the unslotted thickness T band and the slot width S band. One reading note: the source prints the series identity per result but no standard number, so a standards-controlled requirement should name the controlling standard explicitly on the RFQ.

Type / scope inch-series heavy hex slotted nuts, nominal sizes 1/4 to 1 1/2 in; the source calculator prints the "Heavy Hex Slotted Nut" product identity on every captured result (type-descriptor registration — no standard number printed on the results)
Form slotted (castellated) hex nut, heavy series: heavy width across flats with a slotted top face accepting a cotter pin or slotted spring pin for positive anti-rotation lock
Width across flats F basic printed per size in fractions with F max/min decimals: 1/2 (0.500/0.488) at 1/4, 9/16 at 5/16, 1 1/4 (1.250/1.212) at 3/4, up to 2 3/8 (2.375/2.307) at 1 1/2
Width across corners G max/min printed per size (0.577/0.556 at 1/4 up to 2.598/2.480 at 1 1/2) — the clearance check for adjacent walls and wrench swing
Thickness H basic/max/min printed per size (15/64 in, 0.250/0.218 at 1/4 rising to 1 15/32 in, 1.526/1.474 at 1 1/2) — the heavy-series section
Unslotted thickness T max/min printed per size (0.15/0.13 at 1/4 up to 1.08/1.04 at 1 1/2) — the thread-engagement length below the slot
Slot width S max/min printed per size (0.10/0.07 at 1/4 rising to 0.46/0.37 at 1 1/2) — sizes the cotter pin or slotted spring pin for the lock
Family context the same source capture covers the plain hex slotted series (registered separately as asme-b18-2-2-hex-slotted-nuts-inch) and the hex thick series (registered separately); the heavy series is distinguished by its wider flats and its own thickness ladder
Not tabulated sizes above 1 1/2 in, proof load class, thread class (UNC/UNF series implied by the size, not printed per row), MOQ, lead time and price — the last three are confirmed at quotation
Heavy hex slotted nuts, inch series — nominal sizes 1/4 to 1 1/2 in as printed by the sourceAll dimensions in inches as printed by the source (basic fractions; max/min decimals). F = width across flats, G = width across corners, H = thickness, T = unslotted thickness, S = width of slot. Every captured result printed the "Heavy Hex Slotted Nut" product identity.
Nominal sizedF basicF maxF minG maxG minH basicH maxH minT maxT minS maxS min
1/40.25001/20.5000.4880.5770.55615/640.2500.2180.150.130.100.07
5/160.31259/160.5620.5460.6500.62219/640.3140.2800.210.190.120.09
3/80.375011/160.6880.6690.7940.76323/640.3770.3410.240.220.150.12
7/160.43753/40.7500.7280.8660.83027/640.4410.4030.280.260.150.12
1/20.50007/80.8750.8501.0100.96931/640.5040.4640.340.320.180.15
9/160.562515/160.9380.9091.0831.03735/640.5680.5260.370.350.180.15
5/80.62501 1/161.0621.0311.2271.17539/640.6310.5870.400.380.240.18
3/40.75001 1/41.2501.2121.4431.38247/640.7580.7100.490.470.240.18
7/80.87501 7/161.4381.3941.6601.58955/640.8850.8330.620.590.240.18
11.00001 5/81.6251.5751.8761.79663/641.0120.9560.720.690.300.24
1 1/81.12501 13/161.8121.7562.0932.0021 7/641.1391.0790.780.750.330.24
1 1/41.250022.0001.9382.3092.2091 7/321.2511.1870.860.830.400.31
1 3/81.37502 3/162.1882.1192.5262.4161 11/321.3781.3100.990.950.400.31
1 1/21.50002 3/82.3752.3002.7422.6221 15/321.5051.4331.051.010.460.37

Materials

  • Heavy hex slotted nuts order in steel (typically zinc-plated for general service; alloy or stainless where the lock-pin joint sees heavy duty or corrosion); the source page is a dimension reference and does not print material or finish stocks — state the nominal size, thread series and pin diameter on the RFQ. Commercial terms (MOQ, lead time, price) are confirmed at quotation.

Ordering & documentation

Documents

Shipments of Heavy Hex Slotted Nuts (Inch Series) are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for Heavy Hex Slotted Nuts (Inch Series) orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.

Quotation

  • The product family (Heavy Hex Slotted Nuts (Inch Series)), product standard/designation and drawing or part number.
  • The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
  • Material/grade, heat-treatment condition and surface finish, together with the service environment.
  • Quantity per size, delivery destination and required test or traceability documents.

Sample & supply

Supply source for Heavy Hex Slotted Nuts (Inch Series): own manufacturing plus qualified outsourcing (per the owner-confirmed scope of supply (own production plus outsourcing)).

Minimum order quantity for heavy hex slotted nuts (inch series) is 10,000 pieces (applies to the standard sizes and finishes for heavy hex slotted nuts (inch series); mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for heavy hex slotted nuts (inch series) run 3–7 days. Quantities or variants of heavy hex slotted nuts (inch series) outside the standard range are confirmed at quotation.

Storage & shipping

Heavy Hex Slotted Nuts (Inch Series) are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store heavy hex slotted nuts (inch series) dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.

Frequently asked questions

Heavy hex slotted versus plain hex slotted — what does the heavy series actually buy?

Two things, both visible in the table. First, wrench size: the heavy series takes a wider across-flats dimension at the same nominal size (1/2 in at 1/4 nominal versus 7/16 for the plain series), which spreads the torquing load and pairs with heavy hex bolts whose heads need the same larger wrench. Second, section: the thickness ladder runs taller than the plain series at the larger sizes, giving more thread engagement for the higher clamps the heavy series is chosen for. The slot itself works identically in both — torque the nut, align a slot with the pre-drilled hole, insert the pin. So the choice is driven by the bolt (heavy hex bolt heads demand the heavy nut) and the load, not by the locking method.

How do I pick the cotter pin size from this table?

From the S column: the slot width max/min band per size is the groove the pin must fit — a 1/4 heavy slotted nut takes a pin through a 0.10 in max slot, while 1 1/2 takes 0.46 in. The pin diameter is chosen at or just under the slot's nominal width so it passes through the aligned slot and the drilled hole in the bolt with a snug interference against rotation. Note the table sizes the slot, not the cross-drilled hole; the hole in the bolt is sized to the pin, and the alignment tolerance (whether a slot always lands over the hole at proper torque) is a stack-up question on the assembly, not something the nut table can promise. State the intended pin diameter on the RFQ if you want the match confirmed.

The source prints no standard number — how should a standards-controlled requirement be specified?

By naming the controlling standard explicitly. This page is registered as a type-descriptor: the source calculator prints the product identity and the dimension band per result, but no standard designation on the captured results, and this table keeps every cell traceable to that print rather than back-filling numbers from a standard document. If your drawing or procurement system requires a standard-numbered callout, put that number on the RFQ alongside the size — the offer confirms the part against the named standard, and the table here serves as the geometric cross-check that the size line is the one you meant.

Request a Quote

Get factory-direct pricing from the manufacturer.

What to include in your Heavy Hex Slotted Nuts (Inch Series) inquiry

  • ✓ Name the nut standard, style and nominal thread size/pitch, including metric or inch thread series.
  • ✓ State the nut property class or material and the bolt class/material it must be paired with.
  • ✓ Specify locking or prevailing-torque feature, coating and corrosion environment.
  • ✓ Give quantity per size, destination and any lot or mechanical-test documentation.
  • ✓ Factory-direct pricing for your Heavy Hex Slotted Nuts (Inch Series)
  • ✓ Standard and custom specifications
  • ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
  • ✓ Full fastener family support

We use your details only to answer this inquiry — see our Privacy notice for everything the form collects.