DIN EN ISO 4036 Hexagon Thin Nuts (Unchamfered), Product Grade B

DIN EN ISO 4036-2001 hexagon thin nuts, unchamfered, product grade B: pitch-keyed ladder P 0.35 to 1.5 with width across flats s, width across corners e and thickness m max/min per column.

Last updated: 2026-11

Request a Quote

DIN EN ISO 4036 Hexagon Thin Nuts (Unchamfered), Product Grade B in an industrial setting
Illustrative image redrawn from real DIN EN ISO 4036 Hexagon Thin Nuts (Unchamfered), Product Grade B product references — not a photograph of stocked items.

Specifications

ISO 4036 is the hex thin nut without the chamfered bearing face — the lowest-profile hex nut in the metric ladder, and the one whose top surface is flat to the corners rather than washer-faced at 30°. The collected 2001 DIN EN edition table keys its ten columns by pitch only (P 0.35, 0.4, 0.45, 0.5, 0.6, 0.7, 0.8, 1, 1.25, 1.5 — the grid prints no size-designation header row, so each column identifies by its pitch) and prints, per column: width across flats s max/nominal 3.2 up to 16 with s min 2.9 to 15.57, width across corners e min 3.28 to 17.59 (the wrench-fit check — a nut worn below e min rounds in the spanner), and thickness m max 1 up to 5 with m min 0.75 to 4.7. "Product grade B" is the dimensional-accuracy class of the title: the tighter of the two general nut grades, matched to the tolerance of the bolt it pairs with. Against the chamfered thin nuts this site already carries (ISO 4035, DIN 936), the unchamfered form is a distinct identity: the flat top seats on soft material or shallow clearances where a chamfer would dig or where the stack has no room for the washer-faced step, while the chamfered versions spin on more easily and centre better on the bolt — the drawing's call-out decides, and it is not a substitution to make silently.

Standard / scope DIN EN ISO 4036-2001 hexagon thin nuts (unchamfered), product grade B — pitch-keyed ladder P 0.35 to 1.5, ten columns as tabulated
Pitch key P 0.35, 0.4, 0.45, 0.5, 0.6, 0.7, 0.8, 1, 1.25, 1.5 — the grid prints no size-designation header row; each column identifies by its pitch
Width across flats s max=nominal 3.2/4/5/5.5/6/7/8/10/13/16; min 2.9/3.7/4.7/5.2/5.7/6.64/7.64/9.64/12.57/15.57
Width across corners e min 3.28/4.18/5.31/5.88/6.44/7.5/8.63/10.89/14.2/17.59
Thickness m max 1/1.2/1.6/1.8/2/2.2/2.7/3.2/4/5; min 0.75/0.95/1.35/1.55/1.75/1.95/2.45/2.9/3.7/4.7
Not tabulated Strength/property class, proof loads, finish — per RFQ
DIN EN ISO 4036 hexagon thin nuts (unchamfered), product grade B — attribute ladder by sizeMillimetres. The source prints an attribute-label grid positionally paired with a numeric grid; merged rows carry the label cells verbatim followed by the values. The numeric grid keys sizes by pitch only (P row 0.35 to 1.5) and prints no size-designation header row — each column identifies by its pitch, per the fail-closed discipline no size designations are inferred here.
AttributeSub-label
PPitch0.350.40.450.50.60.70.811.251.5
emin3.284.185.315.886.447.58.6310.8914.217.59
mmax11.21.61.822.22.73.245
mmin0.750.951.351.551.751.952.452.93.74.7
smax=nominal size3.2455.5678101316
smin2.93.74.75.25.76.647.649.6412.5715.57
  • The numeric grid prints pitch values only (P 0.35 to 1.5) with no size-designation header row; sizes identify by pitch column. The label grid rows are exactly two cells — no padding.

Materials

  • Product grade B is a dimensional class, not a strength class — the collected page prints no property-class or proof-load rows, so the material pairing with the mating bolt is confirmed per order, not claimed from the table. Unchamfered thin nuts order by the pitch column of the thread they pair with; state thread size and pitch, the mating bolt's property class, and finish on the RFQ. Lead time, MOQ and price: contact for confirmation.

Ordering & documentation

Documents

Shipments of DIN EN ISO 4036 Hexagon Thin Nuts (Unchamfered), Product Grade B are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for DIN EN ISO 4036 Hexagon Thin Nuts (Unchamfered), Product Grade B orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.

Quotation

  • The product family (DIN EN ISO 4036 Hexagon Thin Nuts (Unchamfered), Product Grade B), product standard/designation and drawing or part number.
  • The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
  • Material/grade, heat-treatment condition and surface finish, together with the service environment.
  • Quantity per size, delivery destination and required test or traceability documents.

Sample & supply

Supply source for DIN EN ISO 4036 Hexagon Thin Nuts (Unchamfered), Product Grade B: own manufacturing plus qualified outsourcing (per the owner-confirmed scope of supply (own production plus outsourcing)).

Minimum order quantity for din en iso 4036 hexagon thin nuts (unchamfered), product grade b is 10,000 pieces (applies to the standard sizes and finishes for din en iso 4036 hexagon thin nuts (unchamfered), product grade b; mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for din en iso 4036 hexagon thin nuts (unchamfered), product grade b run 3–7 days. Quantities or variants of din en iso 4036 hexagon thin nuts (unchamfered), product grade b outside the standard range are confirmed at quotation.

Storage & shipping

DIN EN ISO 4036 Hexagon Thin Nuts (Unchamfered), Product Grade B are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store din en iso 4036 hexagon thin nuts (unchamfered), product grade b dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.

Frequently asked questions

Unchamfered — when does that matter compared with the chamfered ISO 4035 / DIN 936 thin nuts?

Two places. Bearing: the chamfer on a 4035/936 nut relieves the outer edge of the top face, so the nut seats on a washer or a machined face without the corner digging in; an unchamfered 4036 nut has the full flat to the corners, which suits soft bearing material or thin flanges where you want maximum bearing area — but on a rough or unprepared surface its corners can bridge instead of seating. Fit: the chamfer also guides the nut onto the bolt and centres it in clearance holes; unchamfered nuts are fussier to start. The collected table itself carries no interchangeability note, and none should be assumed — if the drawing says ISO 4036, the flat top is part of the call-out; substitute only with the mating part's agreement in writing.

The table has no size labels — how do I find my nut?

By pitch. The grid keys each column by thread pitch (P 0.35 up to 1.5) and prints no M-designations, so the fail-closed reading is: know your thread's pitch, read that column straight down for s, e and m. This matters most at the fine-pitch end of the ladder, where the same across-flats width can belong to more than one nominal size and the thickness is what differs — quoting "a 13 mm thin nut" without the pitch is ambiguous, while "P 1.25" is not. Send the full thread call-out (size and pitch, e.g. from the bolt it mates) on the RFQ and we ship the column that matches; we will not guess a size from width alone.

What is the MOQ and lead time for DIN EN ISO 4036 Hexagon Thin Nuts (Unchamfered), Product Grade B?

Orders under this designation have a minimum order quantity of 10,000 pieces. Stock items ship in 3–7 days. Final commercial terms are confirmed per quotation.

What should an RFQ for DIN EN ISO 4036 Hexagon Thin Nuts (Unchamfered), Product Grade B state?

State the full designation (DIN EN ISO 4036 Hexagon Thin Nuts (Unchamfered), Product Grade B), thread size and pitch or diameter, length or head dimension, finish, quantity per size, plus the destination country and any required certificate such as a mill test report per EN 10204 3.1; dimensions and schedule for this designation are confirmed with the quotation.

Request a Quote

Get factory-direct pricing from the manufacturer.

What to include in your DIN EN ISO 4036 Hexagon Thin Nuts (Unchamfered), Product Grade B inquiry

  • ✓ Name the nut standard, style and nominal thread size/pitch, including metric or inch thread series.
  • ✓ State the nut property class or material and the bolt class/material it must be paired with.
  • ✓ Specify locking or prevailing-torque feature, coating and corrosion environment.
  • ✓ Give quantity per size, destination and any lot or mechanical-test documentation.
  • ✓ Factory-direct pricing for your DIN EN ISO 4036 Hexagon Thin Nuts (Unchamfered), Product Grade B
  • ✓ Standard and custom specifications
  • ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
  • ✓ Full fastener family support

We use your details only to answer this inquiry — see our Privacy notice for everything the form collects.