Hex Thick Slotted Nuts (Inch Series)
Hex thick slotted nuts, inch series, 1/4 to 1 1/2 in nominal — the extra-thick castellated hex nut on standard-series width across flats, with the full F/G/H/T/S dimension bands tabulated per size as printed by the source.
Last updated: 2026-11
Specifications
Hex thick slotted nuts keep the standard-series wrench size but add height: the thickness ladder here runs meaningfully taller than both the plain and heavy slotted series at the same nominal size (9/32 in basic at 1/4 against 7/32 plain and 15/64 heavy), with the extra metal going into thread engagement below the slot. That is the design intent — a castellated nut chosen where the joint wants maximum engaged thread and positive pin lock but the wrench inventory or the surrounding geometry is already fixed to standard-series flats. The trade-off shows up in stack height: the T (unslotted) band plus the slot crown needs clearance above the joint, so these nuts suit through-bolted assemblies where the bolt can protrude. As with the heavy series, the source prints the series identity per captured result but no standard number — a standards-controlled requirement names the standard on the RFQ. The table carries the whole printed band per size, from the 1/4 line (F 7/16, H 9/32, S 0.10 max) to 1 1/2 (F 2 1/4, H 1 1/2, S 0.46 max).
| Type / scope | inch-series hex thick slotted nuts, nominal sizes 1/4 to 1 1/2 in; the source calculator prints the "Hex Thick Slotted Nut" product identity on every captured result (type-descriptor registration — no standard number printed on the results) |
|---|---|
| Form | slotted (castellated) hex nut, thick series: standard-series width across flats with an extra-thick section and a slotted top face for cotter pin or slotted spring pin lock |
| Width across flats | F basic printed per size in fractions with F max/min decimals: 7/16 (0.438/0.428) at 1/4, 9/16 at 3/8, 1 1/8 at 3/4, up to 2 1/4 (2.250/2.175) at 1 1/2 — standard-series wrench sizes throughout |
| Width across corners | G max/min printed per size (0.505/0.488 at 1/4 up to 2.598/2.480 at 1 1/2) |
| Thickness | H basic/max/min printed per size (9/32 in, 0.288/0.274 at 1/4 rising to 1 1/2 in, 1.526/1.474 at 1 1/2) — the tall section that distinguishes the thick series from plain and heavy |
| Unslotted thickness | T max/min printed per size (0.20/0.18 at 1/4 up to 1.08/1.04 at 1 1/2) — the thread-engagement length below the slot, taller than the plain series at every size |
| Slot width | S max/min printed per size (0.10/0.07 at 1/4 rising to 0.46/0.37 at 1 1/2) — sizes the cotter pin or slotted spring pin for the lock |
| Family context | the same source capture covers the plain series (registered as asme-b18-2-2-hex-slotted-nuts-inch) and the heavy series (registered separately); the thick series keeps standard-series flats while running the tallest thickness ladder of the three |
| Not tabulated | sizes above 1 1/2 in, proof load class, thread class (UNC/UNF series implied by the size, not printed per row), MOQ, lead time and price — the last three are confirmed at quotation |
| Nominal size | d | F basic | F max | F min | G max | G min | H basic | H max | H min | T max | T min | S max | S min |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 1/4 | 0.2500 | 7/16 | 0.438 | 0.428 | 0.505 | 0.488 | 9/32 | 0.288 | 0.274 | 0.20 | 0.18 | 0.10 | 0.07 |
| 5/16 | 0.3125 | 1/2 | 0.500 | 0.489 | 0.577 | 0.557 | 21/64 | 0.336 | 0.320 | 0.24 | 0.22 | 0.12 | 0.09 |
| 3/8 | 0.3750 | 9/16 | 0.562 | 0.551 | 0.650 | 0.628 | 13/32 | 0.415 | 0.398 | 0.29 | 0.27 | 0.15 | 0.12 |
| 7/16 | 0.4375 | 11/16 | 0.688 | 0.675 | 0.794 | 0.768 | 29/64 | 0.463 | 0.444 | 0.31 | 0.29 | 0.15 | 0.12 |
| 1/2 | 0.5000 | 3/4 | 0.750 | 0.736 | 0.866 | 0.840 | 9/16 | 0.573 | 0.552 | 0.42 | 0.40 | 0.18 | 0.15 |
| 9/16 | 0.5625 | 7/8 | 0.875 | 0.861 | 1.010 | 0.982 | 39/64 | 0.621 | 0.598 | 0.43 | 0.41 | 0.18 | 0.15 |
| 5/8 | 0.6250 | 15/16 | 0.938 | 0.922 | 1.083 | 1.051 | 23/32 | 0.731 | 0.706 | 0.51 | 0.49 | 0.24 | 0.18 |
| 3/4 | 0.7500 | 1 1/8 | 1.125 | 1.088 | 1.299 | 1.240 | 13/16 | 0.827 | 0.798 | 0.57 | 0.55 | 0.24 | 0.18 |
| 7/8 | 0.8750 | 1 5/16 | 1.312 | 1.269 | 1.516 | 1.447 | 29/32 | 0.922 | 0.890 | 0.67 | 0.64 | 0.24 | 0.18 |
| 1 | 1.0000 | 1 1/2 | 1.500 | 1.450 | 1.732 | 1.653 | 1 | 1.018 | 0.982 | 0.73 | 0.70 | 0.30 | 0.24 |
| 1 1/8 | 1.1250 | 1 11/16 | 1.688 | 1.631 | 1.949 | 1.859 | 1 5/32 | 1.176 | 1.136 | 0.83 | 0.80 | 0.33 | 0.24 |
| 1 1/4 | 1.2500 | 1 7/8 | 1.875 | 1.812 | 2.165 | 2.066 | 1 1/4 | 1.272 | 1.228 | 0.89 | 0.86 | 0.40 | 0.31 |
| 1 3/8 | 1.3750 | 2 1/16 | 2.062 | 1.994 | 2.382 | 2.273 | 1 3/8 | 1.399 | 1.351 | 1.02 | 0.98 | 0.40 | 0.31 |
| 1 1/2 | 1.5000 | 2 1/4 | 2.250 | 2.175 | 2.598 | 2.480 | 1 1/2 | 1.526 | 1.474 | 1.08 | 1.04 | 0.46 | 0.37 |
Materials
- Hex thick slotted nuts order in steel (typically zinc-plated for general service; stainless for corrosive duty); the source page is a dimension reference and does not print material or finish stocks — state the nominal size, thread series and pin diameter on the RFQ. Commercial terms (MOQ, lead time, price) are confirmed at quotation.
Ordering & documentation
Documents
Shipments of Hex Thick Slotted Nuts (Inch Series) are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for Hex Thick Slotted Nuts (Inch Series) orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.
Quotation
- The product family (Hex Thick Slotted Nuts (Inch Series)), product standard/designation and drawing or part number.
- The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
- Material/grade, heat-treatment condition and surface finish, together with the service environment.
- Quantity per size, delivery destination and required test or traceability documents.
Sample & supply
Supply source for Hex Thick Slotted Nuts (Inch Series): own manufacturing plus qualified outsourcing (per the owner-confirmed scope of supply (own production plus outsourcing)).
Minimum order quantity for hex thick slotted nuts (inch series) is 10,000 pieces (applies to the standard sizes and finishes for hex thick slotted nuts (inch series); mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for hex thick slotted nuts (inch series) run 3–7 days. Quantities or variants of hex thick slotted nuts (inch series) outside the standard range are confirmed at quotation.
Storage & shipping
Hex Thick Slotted Nuts (Inch Series) are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store hex thick slotted nuts (inch series) dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.
Frequently asked questions
Thick versus heavy hex slotted — both are taller than plain, so which one is for my joint?
The decisive difference is the wrench, not the thickness. The heavy series pairs with heavy hex bolt heads: wider across flats at every nominal size, so the wrench inventory changes with it. The thick series keeps standard-series flats — a 1/4 thick slotted nut takes the same 7/16 wrench as the plain one — and buys its extra strength purely through height (9/32 in basic at 1/4, taller still at the top of the range). So: if the bolt is a heavy hex bolt, the nut is heavy hex slotted; if the bolt and wrenching are standard series but the joint wants maximum engaged thread plus pin lock, the thick slotted nut is the fit. The G (corners) column also differs at equal nominal size, which matters where the nut sits next to a wall.
What does the extra height cost in assembly?
Stack height and bolt protrusion. The thick series carries the tallest H band of the three slotted series at every nominal size, and the castellation adds the slot crown above that, so the bolt must protrude far enough for the slots to clear the joint face and align with the cross-hole — the T column (unslotted thickness) is the minimum engaged thread below the slot, and the clearance question is whether total height plus crown fits the assembly without bottoming. On blind-hole or flush-protrusion assemblies that extra height can be the disqualifier; where the bolt can run long, the thick series rewards you with the deepest thread engagement and the same pin-lock behavior as the other slotted series. The table's H and T bands per size are the numbers to run that stack-up against.
Why does this table stop at 1 1/2 in, and what should a larger requirement do?
The source calculator serves sizes 1/4 through 1 1/2 in nominal, and the table keeps exactly that print — sizes above 1 1/2 exist in the series but are not on this capture, and numbers carried in from another reference would break the traceability rule that every cell here maps to a displayed source value. The gap is disclosed rather than filled. For requirements above 1 1/2 in, state the nominal size and thread series on the RFQ: the confirming dimensions and the controlling standard come back with the offer, and this table still serves as the geometric pattern (F, G, H, T, S stepping with size) that the quoted line should follow.
Request a Quote
Get factory-direct pricing from the manufacturer.
What to include in your Hex Thick Slotted Nuts (Inch Series) inquiry
- ✓ Name the nut standard, style and nominal thread size/pitch, including metric or inch thread series.
- ✓ State the nut property class or material and the bolt class/material it must be paired with.
- ✓ Specify locking or prevailing-torque feature, coating and corrosion environment.
- ✓ Give quantity per size, destination and any lot or mechanical-test documentation.
- ✓ Factory-direct pricing for your Hex Thick Slotted Nuts (Inch Series)
- ✓ Standard and custom specifications
- ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
- ✓ Full fastener family support