DIN 80705 Thin Nuts with Fine Pitch Thread and Small Widths Across Flats
DIN 80705 thin nuts with fine pitch thread and small widths across flats: hexagon series M12x1,5 to M52x2 and octagon series M56 to M140x6 — low-height 14H steel (brass lane) lock/adjustment nuts collected with e min., m height, s width and a per-piece reference weight.
Last updated: 2026-11
Specifications
DIN 80705 is the thin nut for fine pitch threads — a low-height, narrow-across-flats nut used where a standard hex nut is too tall or too wide: locking against another nut, adjusting position on a fine-thread stud, or seating in tight clearance. The collected page splits its ladder into two series it names itself: Series 1 - Octagon runs the large sizes M56 through M140x6 (mostly x6 fine pitch from M72 up), where an octagon flank pattern gives the wrench a wider landing on very large widths — s climbs from 70 to 165 mm; Series 2 - Hexagon runs the fine-pitch small and mid sizes M12x1,5 through M52x2 (1,5 mm pitch through M26, 2 mm from M30), s from 17 to 65, and its table carries both Hexagon and Octagon width sub-columns per row — every size through M45 prints hexagon values, while M52x2 prints only an octagon width (65). Height m stays thin across both series: 6 to 10 mm in Series 2, 22 to 35 mm in the large octagon ladder, never a full-duty nut height. Materials per the Makings panel: steel 14H, brass; stainless prints "-". The page also prints a per-piece reference weight — useful when quoting large octagon nuts, which run from 0,32 kg at M56 to about 2,2 kg at M140x6. Where the application is a fine-thread adjustment or locknut on small-mid threads, Series 2 is the identity; for large plant studs and equipment threads, Series 1.
| Standard / scope | DIN 80705 thin nuts with fine pitch thread and small widths across flats — two series as the source labels them: Series 1 - Octagon M56 to M140x6 (18 sizes), Series 2 - Hexagon M12x1,5 to M52x2 (13 sizes) |
|---|---|
| Fine pitch threads | Series 2: 1,5 mm pitch through M26x1,5, 2 mm from M30x2; Series 1: x6 pitch from M72x6 up (M56/M60/M64/M68 print plain designations — pitch not restated per row) |
| Width across flats s | Series 1 (octagon): 70 to 165 mm; Series 2: hexagon 17 to 55 with an octagon sub-column printed per row (all "-" except M52x2, which prints octagon 65) — per the source's split sub-header |
| Height m | Series 2: 6 to 10 mm; Series 1: 22 to 35 mm — thin-nut heights throughout, no full-duty heights tabulated |
| e min. (circumscribed circle) | Series 2: 18,72 (M12x1,5) to 70,3 (M52x2); Series 1: 75,7 (M56) to 179 (M140x6) — per the legend "not less than" |
| Reference weight | Per-piece "weight kg/pc": Series 2 0,7 to 11,2; Series 1 0,32 to 2,2 — source values verbatim including bare "1" at M100x6 |
| Materials / thread | Steel 14H, Non Ferrous Brass, Stainless "-", Plastic "-", thread 6H — per the Makings panel; finishes per RFQ |
| Not tabulated | Proof-load or tightening ratings, surface finishes, stainless lane (prints "-") — per RFQ |
| Thread d | e min. | m | s | weight kg/pc |
|---|---|---|---|---|
| M56 | 75,7 | 22 | 70 | 0,32 |
| M60 | 81,2 | 22 | 75 | 0,36 |
| M64 | 86,6 | 24 | 80 | 0,45 |
| M68 | 92 | 24 | 85 | 0,51 |
| M72x6 | 97,4 | 24 | 90 | 0,56 |
| M76x6 | 103 | 26 | 95 | 0,67 |
| M80x6 | 108 | 26 | 100 | 0,74 |
| M85x6 | 114 | 26 | 105 | 0,81 |
| M90x6 | 119 | 26 | 110 | 0,84 |
| M95x6 | 124 | 28 | 115 | 0,95 |
| M100x6 | 130 | 28 | 120 | 1 |
| M105x6 | 141 | 28 | 130 | 1,3 |
| M110x6 | 141 | 28 | 130 | 1,1 |
| M115x6 | 146 | 30 | 135 | 1,2 |
| M120x6 | 157 | 30 | 145 | 1,5 |
| M125x6 | 162 | 30 | 150 | 1,7 |
| M130x6 | 168 | 30 | 155 | 1,7 |
| M140x6 | 179 | 35 | 165 | 2,2 |
- Row 13 (M110x6): Row M110x6 prints e min. 141 (identical to M105x6, ladder steps 130 -> 141 -> 146 around it) and weight 1,1, below M105x6's 1,3 despite the larger thread - the source's own cells, transcribed verbatim, not normalized; verify against the standard before engineering use.
- Row 11 (M100x6): Row M100x6 prints its weight as bare "1" (integer, no decimal comma) - as printed.
- Series 1 prints a single "s" column; the octagon shape distinction comes from the source's own section label, not a per-row column.
- M56/M60/M64/M68 print plain designations (no x-pitch restatement per row) - as printed; thread is 6H per the Makings panel.
| Thread d | e min. | m | s (Hexagon) | s (Octagon) | weight kg/pc |
|---|---|---|---|---|---|
| M12x1,5 | 18,72 | 6 | 17 | - | 0,7 |
| M14x1,5 | 20,88 | 6 | 19 | - | 0,82 |
| M16x1,5 | 23,91 | 6 | 22 | - | 1,1 |
| M18x1,5 | 26,17 | 6 | 24 | - | 1,2 |
| M20x1,5 | 29,56 | 6 | 27 | - | 1,6 |
| M22x1,5 | 32,95 | 7 | 30 | - | 2,3 |
| M24x1,5 | 35,03 | 7 | 32 | - | 2,5 |
| M26x1,5 | 39,55 | 8 | 36 | - | 4 |
| M30x2 | 45,2 | 8 | 41 | - | 5 |
| M36x2 | 50,85 | 9 | 46 | - | 6,2 |
| M42x2 | 55,37 | 9 | 50 | - | 5,9 |
| M45x2 | 60,79 | 9 | 55 | - | 7,7 |
| M52x2 | 70,3 | 10 | - | 65 | 11,2 |
- Row 11 (M42x2): Row M42x2 prints weight 5,9, below M36x2's 6,2 despite the larger thread - verbatim, flagged, not normalized.
- The s (Octagon) sub-column prints "-" for every size except M52x2 (octagon 65) - the source's own split-sub-header state, carried as printed.
- Legend covers s/e/m/d only; P (pitch) appears only in the thread designations (M12x1,5 ... M52x2) and has no legend entry.
Materials
- The collected Makings panel lists steel 14H and brass, with stainless and plastic printing "-". A 14H thin nut is a lock/adjustment component, not a structural joint member — it clamps against a shoulder or a mating nut rather than carrying the joint preload, so the mating stud's strength class governs the assembly. Brass versions serve electrical and spark-safe tooling where the fine pitch adjustment matters. Confirm material and finish on the RFQ; the stainless lane is quoted from current stock, not from this table.
Ordering & documentation
Documents
Shipments of DIN 80705 Thin Nuts with Fine Pitch Thread and Small Widths Across Flats are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for DIN 80705 Thin Nuts with Fine Pitch Thread and Small Widths Across Flats orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.
Quotation
- The product family (DIN 80705 Thin Nuts with Fine Pitch Thread and Small Widths Across Flats), product standard/designation and drawing or part number.
- The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
- Material/grade, heat-treatment condition and surface finish, together with the service environment.
- Quantity per size, delivery destination and required test or traceability documents.
Sample & supply
Supply source for DIN 80705 Thin Nuts with Fine Pitch Thread and Small Widths Across Flats: own manufacturing plus qualified outsourcing (per the owner-confirmed scope of supply (own production plus outsourcing)).
Minimum order quantity for din 80705 thin nuts with fine pitch thread and small widths across flats is 10,000 pieces (applies to the standard sizes and finishes for din 80705 thin nuts with fine pitch thread and small widths across flats; mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for din 80705 thin nuts with fine pitch thread and small widths across flats run 3–7 days. Quantities or variants of din 80705 thin nuts with fine pitch thread and small widths across flats outside the standard range are confirmed at quotation.
Storage & shipping
DIN 80705 Thin Nuts with Fine Pitch Thread and Small Widths Across Flats are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store din 80705 thin nuts with fine pitch thread and small widths across flats dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.
Frequently asked questions
Why does DIN 80705 use fine pitch threads — and when does that matter?
Fine pitch is the point of the designation. A finer thread advances less per turn, so a thin nut on a fine-pitch stud gives finer adjustment — bearing-lock position, backlash take-up, clearance setting — and the low height keeps the stack short. The collected ladder prints the pitches: 1,5 mm on M12 through M26, 2 mm from M30 through M52, and x6 across the large octagon series from M72 up. When ordering, the pitch is part of the designation (M20x1,5, not M20) — a coarse-thread nut will run onto a fine-pitch stud only until it binds, and the mistake often damages the stud. Match the designation letter-for-letter against your drawing callout.
The table prints odd values at M110x6 (e min. 141, weight 1,1) — can I rely on that row?
Read it as printed but verify it before engineering use. The row's e min. 141 is identical to M105x6's 141 while the ladder steps 130 → 141 → 146 around it, and its weight 1,1 kg/pc sits below M105x6's 1,3 despite the larger thread — the collected page flags nothing, and this page transcribes verbatim and flags rather than correcting (the pattern suggests a copy slip, but that is inference, not source). The same applies to M42x2's weight 5,9, below M36x2's 6,2. For quoting, weight discrepancies are minor; for machining a housing pocket that clears the nut corners, e min. is the dimension that matters — confirm that one against the standard or a second source before cutting metal.
What should an RFQ for DIN 80705 thin nuts state?
State the designation (DIN 80705), the thread with its pitch (M20x1,5 / M30x2 / M140x6 style), series if your drawing distinguishes octagon from hexagon widths (Series 1 octagon for the large sizes, Series 2 hexagon through M45, M52x2 octagon), material — steel 14H or brass per the collected panel — finish if not plain, and quantity per size. For the large octagon sizes, the per-piece weight column gives a first quoting reference; commercial terms are confirmed at quotation.
Request a Quote
Get factory-direct pricing from the manufacturer.
What to include in your DIN 80705 Thin Nuts with Fine Pitch Thread and Small Widths Across Flats inquiry
- ✓ Name the nut standard, style and nominal thread size/pitch, including metric or inch thread series.
- ✓ State the nut property class or material and the bolt class/material it must be paired with.
- ✓ Specify locking or prevailing-torque feature, coating and corrosion environment.
- ✓ Give quantity per size, destination and any lot or mechanical-test documentation.
- ✓ Factory-direct pricing for your DIN 80705 Thin Nuts with Fine Pitch Thread and Small Widths Across Flats
- ✓ Standard and custom specifications
- ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
- ✓ Full fastener family support