Hex Machine Screw Nuts (Inch Series)

Inch-series hex machine screw nuts — the small hex nuts paired with machine screw sizes, tabulated here for the nominal diameters 0.060 to 0.099 in as printed by the source, with width across flats/corners and the thickness band per size.

Last updated: 2026-11

Request a Quote

Hex Machine Screw Nuts (Inch Series) in an industrial setting
Illustrative image redrawn from real Hex Machine Screw Nuts (Inch Series) product references — not a photograph of stocked items.

Specifications

Machine screw nuts are the small hex nuts that pair with the numbered machine screw series — the sizing convention runs on nominal screw diameter rather than on fraction sizes, which is why the table below reads in diameters (0.060, 0.073, 0.086, 0.099 in) rather than in gauge numbers. They show up wherever machine screws are threaded into metal and need a nut on the far side: electronics chassis, small bracketry, instrument assemblies — anywhere the screw is too small for the standard hex nut series and the joint is permanent enough not to need a Nyflex-style insert. The hex form means the same wrench sizes carry through assembly lines and repair work, and the low profile (thickness runs around half the width across flats) keeps the stack short behind thin sheet. One honesty note about coverage: the recovered ladder covers only the four smallest diameters in the series — larger machine screw nuts exist, but they are not on this print, and a requirement above 0.099 in nominal diameter is a quotation question here, not a table lookup. The source page also prints no standard number; a standard-controlled requirement should name the controlling standard explicitly on the RFQ.

Type / scope inch-series hex machine screw nuts; the source ladder prints nominal screw diameters 0.060, 0.073, 0.086 and 0.099 in — the rest of the machine screw nut range is not tabulated by this capture (gap disclosed, not interpolated)
Form small hex nut paired with the numbered machine screw series; sizes carried as nominal diameters per the source print, with no gauge-number mapping added
Width across flats 5/32 in basic for the 0.060 and 0.073 in diameters (max 0.156 / min 0.150), stepping to 3/16 in basic at 0.086 and 0.099 in (max 0.188 / min 0.180)
Width across corners 0.180 max / 0.171 min at the 5/32 flats; 0.217 max / 0.205 min at the 3/16 flats — the corner clearance check for tight pockets
Thickness 0.050 max / 0.043 min for the two smaller diameters; 0.066 max / 0.057 min for the two larger — roughly a third of the width across flats, the low profile that suits thin sheet stacks
Standard status the source page prints the product identity and dimensions but no standard number; this page is registered as a type-descriptor, and a standard-controlled requirement should name the controlling standard on the RFQ
Anomaly note the source calculator dump repeated the 0.099 in row verbatim; the duplicate was collapsed (values identical) and the coverage ceiling at 0.099 in is carried as printed
Not tabulated diameters above 0.099 in, thread pitch ( UNC machine screw threads are implied by the series but not printed per row), proof load class, MOQ, lead time and price — the last three are confirmed at quotation
Hex machine screw nuts, inch series — nominal diameters 0.060 to 0.099 in as printed by the source (the rest of the machine screw nut range is not tabulated by this capture)All dimensions in inches as printed by the source; sizes are given as nominal screw diameters, with no gauge-number mapping added. The recovered ladder covers only the four smallest diameters — larger machine screw nut sizes exist in the series but are not on this print, and a requirement above 0.099 in is a quotation question here. Thickness is printed as a max/min band (no separate basic).
Nominal diameter (in)Width across flats basicF maxF minWidth across corners maxG minThickness maxThickness min
0.06005/320.1560.150Gmax / 0.1800.1710.0500.043
0.07305/320.1560.150Gmax / 0.1800.1710.0500.043
0.08603/160.1880.180Gmax / 0.2170.2050.0660.057
0.09903/160.1880.180Gmax / 0.2170.2050.0660.057

Materials

  • Machine screw nuts order in steel (typically zinc-plated for general service, with stainless for electronics and corrosive duty); the source page is a dimension reference and does not print material or finish stocks — state the mating machine screw size, material, and finish on the RFQ. Commercial terms (MOQ, lead time, price) are confirmed at quotation.

Ordering & documentation

Documents

Shipments of Hex Machine Screw Nuts (Inch Series) are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for Hex Machine Screw Nuts (Inch Series) orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.

Quotation

  • The product family (Hex Machine Screw Nuts (Inch Series)), product standard/designation and drawing or part number.
  • The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
  • Material/grade, heat-treatment condition and surface finish, together with the service environment.
  • Quantity per size, delivery destination and required test or traceability documents.

Sample & supply

Supply source for Hex Machine Screw Nuts (Inch Series): own manufacturing plus qualified outsourcing (per the owner-confirmed scope of supply (own production plus outsourcing)).

Minimum order quantity for hex machine screw nuts (inch series) is 10,000 pieces (applies to the standard sizes and finishes for hex machine screw nuts (inch series); mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for hex machine screw nuts (inch series) run 3–7 days. Quantities or variants of hex machine screw nuts (inch series) outside the standard range are confirmed at quotation.

Storage & shipping

Hex Machine Screw Nuts (Inch Series) are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store hex machine screw nuts (inch series) dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.

Frequently asked questions

How do machine screw nut sizes relate to the numbered machine screw series?

The table follows the source print and carries sizes as nominal screw diameters: 0.060 in pairs with the No.0 machine screw, 0.073 with No.1, 0.086 with No.2, and 0.099 with No.3 — the nut's thread is cut for the same screw designation as its nominal diameter. The reason the table itself does not say "No.0" is traceability: the source prints diameters, and the gauge-number mapping is added here only as this explanation, not as a table column. Practically, specify the nut by the machine screw it must mate with ("nut for No.2-56") and the diameter column above is the cross-check that the size line is the right one.

Why does the table stop at 0.099 in, when machine screw nuts exist up to larger sizes?

The source page serves dimensions through a per-size calculator, and the recovered ladder covers only the four smallest selections — the larger numbered sizes and the 1/4 in machine screw nut exist in the series but are not on this print. The gap is disclosed rather than filled from another reference, because numbers quoted from a different source would not carry this print's provenance and the fail-closed rule here is to keep every cell traceable. For requirements above 0.099 in, state the mating machine screw size on the RFQ; the confirming dimensions come back with the offer.

What distinguishes a machine screw nut from just using a small hex nut from the standard series?

Proportion and intent. A machine screw nut is sized for the numbered screw series: its width across flats (5/32 and 3/16 in here) and its thin profile (thickness about a third of the flats) match the small screws and thin sheet they clamp, where the smallest standard hex nut would dwarf the assembly. The hex form keeps the wrench inventory shared with the standard series, and the printable corner dimensions (G max/min) matter in electronics chassis where the nut must clear a pocket wall. For anything larger than the numbered series, the standard hex nut series takes over — which is the natural boundary of this page's table.

Request a Quote

Get factory-direct pricing from the manufacturer.

What to include in your Hex Machine Screw Nuts (Inch Series) inquiry

  • ✓ Name the nut standard, style and nominal thread size/pitch, including metric or inch thread series.
  • ✓ State the nut property class or material and the bolt class/material it must be paired with.
  • ✓ Specify locking or prevailing-torque feature, coating and corrosion environment.
  • ✓ Give quantity per size, destination and any lot or mechanical-test documentation.
  • ✓ Factory-direct pricing for your Hex Machine Screw Nuts (Inch Series)
  • ✓ Standard and custom specifications
  • ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
  • ✓ Full fastener family support

We use your details only to answer this inquiry — see our Privacy notice for everything the form collects.