DIN 798 Special Foundation Square Nuts (M24 – M100)
DIN 798 special foundation square nuts — the square companion nut to DIN 797 foundation bolts, tabulated over M24 to M100 with height m 30-125, square size s 50-165 and circumscribed-circle minimum e 65-220; steel with 6H thread as printed.
Last updated: 2026-11
Specifications
DIN 798 is the nut half of the heavy foundation set: a square-section nut sized to run up the same M24 to M100 ladder as the DIN 797 foundation bolt registered alongside it on this site. The square form is the working feature — a square nut resists turning in a cast or chiseled seat (the seat's square pocket, or simply the two flat faces bearing against the foundation, stop rotation while the machine is threaded down onto the bolt's internal thread), which is exactly the assembly the DIN 797/798 pair exists for. The print is a clean ladder: height m runs 30 to 125, square size s 50 to 165, and e — the minimum circumscribed-circle diameter the corners must span — 65 to 220, each row complete across all eleven sizes as captured. The makings block prints a literal "Steel: steel" (no property class given) with thread tolerance 6H — for a nut that seats in concrete and carries the machine seating through a 3.6-class bolt, the grade lives in the geometry, and any class requirement is a quotation confirmation. Practically the buyers are foundation contractors, machine-erection crews and retrofit depots matching hardware to an existing cast-in bolt; the selection rule is to order the pair by the bolt, not the nut: state the DIN 797 thread size and the nut follows the ladder. Match by thread AND seat — s must fit the seat pocket on retrofits, so measure the failed part's s before ordering by thread alone.
| Standard / scope | DIN 798 special foundation square nuts (companion nut to DIN 797 special foundation bolts, registered alongside on this site) |
|---|---|
| Size ladder (d) | M24, M30, M36, M42, M48, M56, M64, M72, M80, M90, M100 — eleven printed sizes, all rows complete |
| Height (m) | 30 / 36 / 45 / 53 / 60 / 70 / 80 / 90 / 100 / 112 / 125 (M24 → M100) |
| Square size (s) | 50 / 60 / 70 / 80 / 90 / 100 / 110 / 120 / 130 / 145 / 165 (M24 → M100) |
| Circumscribed circle (e, not less than) | 65 / 80 / 92 / 105 / 118 / 132 / 145 / 160 / 170 / 190 / 220 (M24 → M100) |
| Materials / thread (as printed) | Steel: steel (no property class printed); Thread: 6H; Stainless: -; Plastic: -; Non Ferrous: - (source makings block verbatim) |
| Not printed | No finish line on the source page — corrosion protection for buried/foundation service is a quotation confirmation |
| row | M24 | M30 | M36 | M42 | M48 | M56 | M64 | M72 | M80 | M90 | M100 |
|---|---|---|---|---|---|---|---|---|---|---|---|
| d | M24 | M30 | M36 | M42 | M48 | M56 | M64 | M72 | M80 | M90 | M100 |
| m | 30 | 36 | 45 | 53 | 60 | 70 | 80 | 90 | 100 | 112 | 125 |
| s | 50 | 60 | 70 | 80 | 90 | 100 | 110 | 120 | 130 | 145 | 165 |
| e | 65 | 80 | 92 | 105 | 118 | 132 | 145 | 160 | 170 | 190 | 220 |
- the makings block prints "Steel: steel" without a property class; Thread: 6H is the only stated fit — no strength-grade claim is made on this page.
- the source prints no finish line — corrosion protection is a quotation confirmation.
Materials
- The source makings block prints "Steel: steel" — a material statement without a property class — with Thread: 6H and a literal "-" for Stainless, Plastic and Non Ferrous. That is consistent with the part's role: the DIN 797/798 foundation pair works by embedding geometry, the bolt is 3.6-class, and the nut's job is to seat square and hold while the machine is threaded down, so the print gives geometry and thread fit (6H) rather than strength grades. This page therefore makes no strength-class claim, and a graded or stainless variant is a quotation item, not a catalogue line. State thread size, square size s (or the seat pocket measurement on retrofits), coating (galvanizing for foundation service is a quotation confirmation), any documentation requirement for the foundation file, and quantity per size — erection crews should order nut and bolt as a matched pair by the bolt's d1 so the two lanes cannot drift apart.
Ordering & documentation
Documents
Shipments of DIN 798 Special Foundation Square Nuts (M24 – M100) are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for DIN 798 Special Foundation Square Nuts (M24 – M100) orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.
Quotation
- The product family (DIN 798 Special Foundation Square Nuts (M24 – M100)), product standard/designation and drawing or part number.
- The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
- Material/grade, heat-treatment condition and surface finish, together with the service environment.
- Quantity per size, delivery destination and required test or traceability documents.
Sample & supply
Supply source for DIN 798 Special Foundation Square Nuts (M24 – M100): own manufacturing plus qualified outsourcing (per the owner-confirmed scope of supply (own production plus outsourcing)).
Minimum order quantity for din 798 special foundation square nuts (m24 – m100) is 10,000 pieces (applies to the standard sizes and finishes for din 798 special foundation square nuts (m24 – m100); mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for din 798 special foundation square nuts (m24 – m100) run 3–7 days. Quantities or variants of din 798 special foundation square nuts (m24 – m100) outside the standard range are confirmed at quotation.
Storage & shipping
DIN 798 Special Foundation Square Nuts (M24 – M100) are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store din 798 special foundation square nuts (m24 – m100) dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.
Frequently asked questions
Why a square nut for foundation work instead of a standard hex nut?
Because the seat, not the torque, holds the joint. During machine erection the nut has to resist turning while the machine component is threaded down the bolt — a square nut bears on two full flat faces against the foundation or its seat pocket, which stops rotation without someone holding a second wrench on an M100-size nut, and in a chiseled or cast square pocket it cannot round off or spin the way a hex can in a degraded seat. The ladder is also sized for the duty: at M48 the height is already 60 mm, giving thread engagement proportional to the coarse foundation threads and the long b1/b2 thread lengths the DIN 797 bolt prints. Where the assembly uses a machine seating with a normal hex, that is a different nut standard — the DIN 798 pairs with the DIN 797 bolt's internal-thread interface specifically.
The makings print just says "steel" — what grade do I actually get?
The source page prints "Steel: steel" with no property class, so this page claims none: the strength is not a printed attribute of the print, and the 6H thread tolerance is the only stated fit. Practically, foundation nuts in this pair work against a 3.6-class bolt — the assembly is sized by embedding geometry, not nut grade — so an ungraded steel nut is the normal supply state. If your foundation specification demands a class (some erection specs do, for inspection paperwork), state it on the RFQ as a requirement to confirm at quotation, and expect documentation to be quoted rather than assumed. What matters dimensionally is the seat: order s to match the pocket, and check e if the corners must clear adjacent hardware.
What should an RFQ for DIN 798 foundation square nuts state?
Thread size (M24-M100 from the ladder — ideally as the matching DIN 797 bolt designation, ordering the pair by the bolt), square size s as a stated dimension (or the measured seat-pocket size on retrofits), the material/coating expectation (source prints plain steel only — galvanizing for buried service is a quotation confirmation), thread tolerance requirement (6H as printed), any foundation documentation requirement, and quantity per size. For retrofits where the original hardware has corroded in place, measure s across the flats before ordering by thread alone — foundation seats are cut for the square, and a nut one size off will not seat even though the thread runs on.
Request a Quote
Get factory-direct pricing from the manufacturer.
What to include in your DIN 798 Special Foundation Square Nuts (M24 – M100) inquiry
- ✓ Name the nut standard, style and nominal thread size/pitch, including metric or inch thread series.
- ✓ State the nut property class or material and the bolt class/material it must be paired with.
- ✓ Specify locking or prevailing-torque feature, coating and corrosion environment.
- ✓ Give quantity per size, destination and any lot or mechanical-test documentation.
- ✓ Factory-direct pricing for your DIN 798 Special Foundation Square Nuts (M24 – M100)
- ✓ Standard and custom specifications
- ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
- ✓ Full fastener family support