DIN 193 Specifications
Dimension table for DIN 193 as printed on the collected technical page — d, d1, s, m from M5 to M16, all measurements in millimetres — with the source's page context (cheese-head and pan-head variants, A2 stainless and brass) and nothing asserted beyond what the collected page shows.
Last updated: 2026-11
Specifications
This page reproduces the collected DIN 193 technical table verbatim: seven rows by four columns — nominal thread d, head diameter d1, width across flats s, and head dimension m — from M5 through M16, under the source's own note "All measurements in millimeters (mm)". The collected page's associated product listings show the standard applied to cheese-head and pan-head screws in plain, A2 stainless and brass, which is the extent of the identity information the collected source itself provides; this page deliberately asserts nothing further about the standard's formal scope, and reads the table as the lookup it is. A buyer holding a DIN 193 callout checks the four dimensions per size exactly as printed — for example M6: d1 14.2, s 10, m 5.5 — and states material, property class and drive on the RFQ, since none of those are tabulated here. Where a drawing's DIN 193 dimensions disagree with the table by more than tolerance, treat the drawing as governing and flag the delta at quotation rather than shipping to the table.
| Table | d / d1 / s / m for M5, M6, M8, M10, M12, M16 — e.g. M5: 11.2 / 8 / 4.3; M8: 18.2 / 13 / 7; M16: 31 / 22 / 14 (verbatim, dimension table below) |
|---|---|
| Units (source note) | All measurements in millimeters (mm) |
| Source page context | The collected page's product listings show cheese-head and pan-head variants in plain, A2 stainless and brass — carried as the source's own context; formal standard scope not asserted |
| Not tabulated | Lengths, thread data, property class, drive, finish — per RFQ |
Materials
- The source page's listings span plain steel, A2 stainless and brass; confirm material and any property-class requirement explicitly on the RFQ — the dimension table is material-independent
Ordering & documentation
Documents
Shipments are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.
Quotation
- The fastener family (DIN 193 Specifications) plus the standard designation from your drawing — DIN / ISO / JIS / ASTM / ANSI, or a drawing for custom parts.
- Size (diameter and length), thread type (metric or inch), property class or grade, and coating or finish.
- Quantity per size and your target delivery date.
- Destination country, and any required documents (for example a mill test certificate) so the quote includes them.
Sample & supply
Minimum order quantity is 10,000 pieces. Stock items run 3–7 days. Quantities or variants outside the standard range are confirmed at quotation.
Storage & shipping
Parts are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store fasteners dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.
Frequently asked questions
The table shows only six sizes (M5-M16) and four dimensions. How do I handle a size or dimension outside the table?
Treat the table as the collected source's complete print, not the standard's complete scope: a callout outside M5-M16, or needing a dimension the four columns do not carry, is a per-RFQ quotation against the governing standard document. This is the honest boundary of collected-page data — the transcription here is verified token-for-token against the live page, but verification of what the source prints is not a claim about what the standard contains. For engineering checks inside the table, read the printed values as delivered geometry targets and hold the drawing as the arbiter on any conflict; for sizes outside it, send the drawing with the RFQ so the quote is made against the callout rather than an extrapolation. Extrapolating dimension ladders beyond their printed end is exactly the kind of quiet guesswork that turns into a fit failure at assembly.
Related knowledge
- Thread-Forming vs Thread-Cutting vs Thread-Rolling Self-Tapping Screws: What the Evidence Settles on Base Material
- Screw Family Selection by Base Material: Wood, Machine and Self-Tapping Threads, Engagement and Coating
- Hex Bolts vs Socket Head Cap Screws: What the Evidence Settles on Strength, Clearance and Cost
Request a Quote
Get factory-direct pricing from the manufacturer.
What to include in your inquiry
- ✓ Standard and property class (e.g. DIN 912, ISO 4762, class 8.8) — or a drawing for custom parts.
- ✓ Sizes, lengths and thread type (metric or inch).
- ✓ Quantity per size and your target delivery date.
- ✓ Destination country, plus any coating or finish requirement.
- ✓ Any documents you need with the shipment (e.g. mill test certificate) so the quote includes them.
- ✓ Your inquiry goes straight to the factory team by email and gets a reply within 24 hours.
- ✓ Factory-direct pricing
- ✓ Standard and custom specifications
- ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
- ✓ Full fastener family support