DIN 6332 Grub Screws with Thrust Point (M6 – M20)
DIN 6332 grub screws with thrust point, M6 to M20 — die-set and ejector positioning set screws with a hardened thrust face, collected per-size table (d2 h11, d3, r, pin length l2, ejector length l3) and a per-100-piece reference weight matrix by length.
Last updated: 2026-11
Specifications
DIN 6332 is the positioning screw of the die-set world: a fine-thread grub screw whose nose carries a hardened thrust point — the source's own note rates that face at 550+100HV — so it can be torqued against a hardened plate, an ejector plate or a stop without galling the surface it pushes on. Where a plain DIN 913 set screw digs a crater into soft steel, this one is made to locate and hold: die sets, mould ejector plates and fixture stops are its natural homes, and its legend says as much (d2 is the "diameter of the ejector", l3 the "length of the ejector" — die-set vocabulary, not general fastener wording). The collected table runs M6 through M20 and prints, per size, the shoulder diameter d2 with an h11 tolerance, the shank d3 at 0/-0,1, the radius r under the head, the pin length l2 and the ejector length l3 — plus a reference-weight matrix by screw length l, printed per 100 pieces, where the source lists only the length/size combinations it actually offers (dashes elsewhere are the source's own gaps, not missing data — other lengths are quoted to drawing). Two printed quirks worth checking before quoting: d2 and d3 come out equal at M10 and M12 in the source, and the tolerances h11 and 0/-0,1 print inline in the first data-cell position of their rows. Steel grades 5.8 and 8.8 with a 6g thread come from the source's materials panel; stainless is printed as "-" there, so it is not claimed, and finishes are per RFQ.
| Standard / scope | DIN 6332 grub screws with thrust point, M6 to M20 (thread d1 is the size ladder itself: M6, M8, M10, M12, M16, M20) |
|---|---|
| Shoulder / ejector diameter | d2 (h11 as printed) 4,5 → 15,5 across the ladder; equal to d3 at M10 and M12 as printed by the source |
| Shank | d3 (0-0,1 as printed) 4 → 14,4 |
| Head radius | r 3 → 13 |
| Pin / ejector lengths | l2 (pin) 6 → 14; l3 (ejector) 2,5 → 5,5 |
| Thrust face hardness | Source note: "trust face 550+100HV" [sic — thrust face] — the hardened nose that sets this screw apart from plain DIN 913 set screws |
| Reference weight | Source "Weight (7,85kg/dm3) kg/100pieces" matrix by length l 30 – 150, per 100 PIECES; sparse matrix, dashes = combinations the source does not list |
| Materials / property classes | Steel 5.8, 8.8; thread 6g (source materials panel). Stainless printed "-" by the source — not claimed; finishes per RFQ |
| d1 | M6 | M8 | M10 | M12 | M16 | M20 |
|---|---|---|---|---|---|---|
| d2 (h11, as printed) | 4,5 | 6 | 8 | 8 | 12 | 15,5 |
| d3 (0-0,1, as printed) | 4 | 5,4 | 7,2 | 7,2 | 11 | 14,4 |
| r | 3 | 5 | 6 | 6 | 9 | 13 |
| l2 (pin length) | 6 | 7,5 | 9 | 10 | 12 | 14 |
| l3 (ejector length) | 2,5 | 3 | 4,5 | 4,5 | 5 | 5,5 |
- Tolerances print as an extra first data cell in the source (d2 row carries h11, d3 row carries 0-0,1 — 8 cells against the 7-cell header, crushed sub-header rowspan); the tolerance attribution is positional-as-printed and is carried in the row labels here, not adjudicated.
- d2 and d3 print equal values at M10 and M12 (8/8 and 7,2/7,2); both rows are transcribed verbatim — the equality is in the source, not a transcription slip.
- The source legend lists l1 ("length of bolt") but the printed table has no l1 column; the legend letter is not invented into a column.
- The source note "trust face 550+100HV" [sic — reads as thrust face] is the source's own hardness statement; carried as printed.
| l | M6 | M8 | M10 | M12 | M16 | M20 |
|---|---|---|---|---|---|---|
| 30 | 0,49 | - | - | - | - | - |
| 40 | - | 1,18 | - | - | - | - |
| 50 | 0,84 | - | - | - | - | - |
| 60 | - | 1,81 | 2,75 | 4,02 | - | - |
| 80 | - | - | 3,75 | 5,48 | 9,96 | - |
| 100 | - | - | - | 6,93 | 12,6 | 19,8 |
| 125 | - | - | - | - | 16 | 24,9 |
| 150 | - | - | - | - | - | 30,1 |
- Sparse matrix by design: the source offers specific l values per thread size (e.g. M6 at l 30 and 50 only, M20 at l 100 and 150 only); the dash cells record the source's own gaps, not missing data. Other lengths are quoted to drawing.
Materials
- Steel, property classes 5.8 or 8.8, thread 6g, per the collected source's materials panel; the source lists no stainless or non-ferrous options, so none are claimed; finish confirmed at quotation (tenant supply range)
Ordering & documentation
Documents
Shipments of DIN 6332 Grub Screws with Thrust Point (M6 – M20) are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for DIN 6332 Grub Screws with Thrust Point (M6 – M20) orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.
Quotation
- The product family (DIN 6332 Grub Screws with Thrust Point (M6 – M20)), product standard/designation and drawing or part number.
- The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
- Material/grade, heat-treatment condition and surface finish, together with the service environment.
- Quantity per size, delivery destination and required test or traceability documents.
Sample & supply
Minimum order quantity for din 6332 grub screws with thrust point (m6 – m20) is 10,000 pieces (applies to the standard sizes and finishes for din 6332 grub screws with thrust point (m6 – m20); mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for din 6332 grub screws with thrust point (m6 – m20) run 3–7 days. Quantities or variants of din 6332 grub screws with thrust point (m6 – m20) outside the standard range are confirmed at quotation.
Storage & shipping
DIN 6332 Grub Screws with Thrust Point (M6 – M20) are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store din 6332 grub screws with thrust point (m6 – m20) dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.
Frequently asked questions
DIN 6332 vs a plain DIN 913 set screw — when does the thrust point matter?
When the screw pushes against something you cannot afford to scar. A plain cone-point set screw (DIN 913) bites into the opposing surface — fine for a permanent lock, wrong for a moving or hardened face. DIN 6332's nose is a thrust point with the source's own face hardness note at 550+100HV, so it transmits a positioning load without digging in: ejector plates that slide, hardened die-set plates, stop faces that must stay smooth after setup. The trade is that it locates rather than locks — where you need anti-loosening as well, pair it with a nut or a locking feature rather than relying on the point biting. Its legend is die-set vocabulary (ejector diameter, ejector length), which is the fastest tell that you are looking at the right standard.
What does an RFQ for DIN 6332 need to state?
Thread size (d1, M6–M20) and length l — the collected weight matrix lists the length/size combinations the source offers (M6 at 30 and 50, M8 at 40 and 60, up to M20 at 100 and 150); other lengths are quoted to drawing. State the property class (5.8 or 8.8 per the collected panel), the contact material of the thrust face if it is anything unusual, quantity, and any certificate requirement such as an EN 10204 3.1 mill report. If the drawing dimensions the mating pocket or ejector bore, send it — d2 (h11) and d3 (0/-0,1) are what the bore sees, and the table on this page gives both per size.
DIN 6332 sits between the DIN 6330 and DIN 6334 numbers — is it part of that nut family?
No — the neighbouring numbers are misleading. DIN 6330 and DIN 6331 are tall clamping nuts (plain and collared) in this catalog's nuts pages; DIN 6332 is a grub screw with a thrust point, a completely different part with a different table. The collected source confirms it: the legend speaks of a screw shank and ejector, the thread is a 6g external screw thread (not the 6H nut thread), and the materials panel lists property classes 5.8/8.8 — screw-side classes. State the part type ("grub screw" vs "clamping nut") alongside the number on the RFQ; a transposed 633x number ships the wrong part entirely.
Related knowledge
- Thread-Forming vs Thread-Cutting vs Thread-Rolling Self-Tapping Screws: What the Evidence Settles on Base Material
- Screw Family Selection by Base Material: Wood, Machine and Self-Tapping Threads, Engagement and Coating
- Hex Bolts vs Socket Head Cap Screws: What the Evidence Settles on Strength, Clearance and Cost
Request a Quote
Get factory-direct pricing from the manufacturer.
What to include in your DIN 6332 Grub Screws with Thrust Point (M6 – M20) inquiry
- ✓ Identify the screw type and standard, including head style and drive recess.
- ✓ Give nominal diameter, thread pitch, length and engagement or hole details where relevant.
- ✓ State the material/property class, substrate material and thickness, and required coating or finish.
- ✓ Describe installation, locking or removal requirements, quantity and destination.
- ✓ Factory-direct pricing for your DIN 6332 Grub Screws with Thrust Point (M6 – M20)
- ✓ Standard and custom specifications
- ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
- ✓ Full fastener family support