DIN 926 Slotted Set Screws with Full Point (M1 – M6)
DIN 926 slotted headless set screws with full (dog) point — micro-to-small sizes M1 to M6 with point and slot attributes dp/n/t dimensioned per size (dp 0,5 to 4,5, slot n 0,2 to 1), property class 5.8 with stainless A1 and brass as printed, for locating micro-assemblies where a headless screw must press a full cylindrical point against or into a mating feature.
Last updated: 2026-11
Specifications
DIN 926 is the headless set screw that ends in a full point: a plain cylindrical dog point of diameter dp that presses flat against a counterbored seat, drops into a hole, or locates a mating part without digging in the way a cone point would. Drive is a simple slot (width n, depth t in the grid), which suits the small sections this standard covers — the collected ladder runs M1 to M6, the micro territory where hex sockets stop being practical and where this screw lives in instruments, optics, jigs and small mechanical assemblies. Three prints on the source page matter when specifying. First, the thread tolerance is asymmetric: 6h at M1,4 but 6g from M1,6 upward — at these sizes the difference is measurable relative to the thread, so the mating thread standard should be checked rather than assumed. Second, the makings line is unusually broad for a set screw: steel class 5.8, stainless A1, and brass as the non-ferrous option — brass matters in electrical and anti-sparking contexts where the steel ladder does not apply. Third, the legend defines l2 (pin length) and l1 (bolt length) but the table prints neither: the point-to-shank proportions come from the standard document, and length is a per-order RFQ dimension this page does not invent.
| Standard / scope | DIN 926 slotted set screws with full point (source title as printed); table title prints "Dimensions screws without head with slot and pin, DIN 926" (double space as captured) |
|---|---|
| Threads | eleven tabulated micro-to-small sizes: M1, M1,2, M1,4, M1,6, M2, M2,5, M3, M3,5, M4, M5, M6 (decimal commas verbatim) |
| Full point diameter (dp) | 0,5 / 0,7 / 0,8 / 0,8 / 1,2 / 1,5 / 2 / 2,5 / 2,8 / 3,5 / 4,5 (M1 → M6) — duplicate adjacent values (0,8 at M1,4/M1,6) as printed |
| Slot (n / t) | slot width n 0,2 to 1; slot depth t 0,4 to 1,6 (decimal commas verbatim) |
| Materials / thread (as printed) | Steel: 5.8; Stainless: A1; Non Ferrous: Brass; Thread: "for size M1,4 - 6h, from size M1,6 - 6g" (source makings block verbatim) |
| Not tabulated | The legend defines l2 (pin length) and l1 (length of bolt) but prints no rows for either — no length ladder and no finishes on the source page; length is a per-order RFQ dimension |
| Attribute | M1 | M1,2 | M1,4 | M1,6 | M2 | M2,5 | M3 | M3,5 | M4 | M5 | M6 |
|---|---|---|---|---|---|---|---|---|---|---|---|
| dp | 0,5 | 0,7 | 0,8 | 0,8 | 1,2 | 1,5 | 2 | 2,5 | 2,8 | 3,5 | 4,5 |
| n | 0,2 | 0,2 | 0,2 | 0,25 | 0,25 | 0,4 | 0,5 | 0,5 | 0,6 | 0,8 | 1 |
| t | 0,4 | 0,4 | 0,48 | 0,56 | 0,64 | 0,72 | 0,8 | 0,96 | 1,12 | 1,28 | 1,6 |
- the source legend also defines l2 - pin length and l1 - length of bolt, but tabulates no dimension rows for either — no length ladder is invented here; length is a per-order RFQ dimension.
- the source thread print is asymmetric: 'for size M1,4 - 6h, from size M1,6 - 6g' — two fit classes across one ladder, carried verbatim (see the page FAQ); thread columns are tabulated without a tolerance column.
- the dp row prints duplicate adjacent values (0,8 at M1,4 and M1,6) and the n row repeats 0,2 and 0,25 and 0,5 — as captured, kept verbatim.
Materials
- The source makings block is unusually wide for a set screw — Steel: 5.8, Stainless: A1, Non Ferrous: Brass — so this page can legitimately offer all three families as printed. The choice is application-driven: class 5.8 steel for general locating duty, A1 stainless for corrosive or washdown instruments, and brass where the screw must not spark, must not magnetize, or must conduct (grounding contact points in electrical assemblies are a classic brass set-screw job). The asymmetric thread print (6h at M1,4, 6g from M1,6) matters most for mixed-material assemblies where a brass screw meets a cut thread — state the tolerance match explicitly. Length (l1) and pin length (l2) are per-order dimensions confirmed at quotation, as the source tabulates neither.
Ordering & documentation
Documents
Shipments of DIN 926 Slotted Set Screws with Full Point (M1 – M6) are backed by Mill Test Certificate (MTC), Dimensional Report, Salt Spray Test Report on request, with full batch traceability from raw material to finished product. Quality management for DIN 926 Slotted Set Screws with Full Point (M1 – M6) orders follows the owner-confirmed compliance list: ISO 9001:2015, RoHS, REACH. Exact document sets are confirmed on the order.
Quotation
- The product family (DIN 926 Slotted Set Screws with Full Point (M1 – M6)), product standard/designation and drawing or part number.
- The dimensions that apply to this part — such as size, pitch, length, thickness, fit, grip or groove geometry.
- Material/grade, heat-treatment condition and surface finish, together with the service environment.
- Quantity per size, delivery destination and required test or traceability documents.
Sample & supply
Minimum order quantity for din 926 slotted set screws with full point (m1 – m6) is 10,000 pieces (applies to the standard sizes and finishes for din 926 slotted set screws with full point (m1 – m6); mixed, special or custom variants are quoted — final commercial terms per quotation) Stock items for din 926 slotted set screws with full point (m1 – m6) run 3–7 days. Quantities or variants of din 926 slotted set screws with full point (m1 – m6) outside the standard range are confirmed at quotation.
Storage & shipping
DIN 926 Slotted Set Screws with Full Point (M1 – M6) are packed for export and shipped factory-direct to buyers in Europe, Asia, the Americas and the Middle East. Store din 926 slotted set screws with full point (m1 – m6) dry and protected until installation, and keep coated parts in their packaging until use; specific packing and preservation requirements can be stated on the order and confirmed at quotation.
Frequently asked questions
Full point vs the other set-screw points — when is DIN 926 the right pick?
The point geometry decides how the screw treats the part it presses against. A full (dog) point ends in a smooth cylinder of diameter dp: it bears flat on a counterbored seat, drops into a drilled hole, or locates a groove without biting — the pick where the mating surface must not be marred, or where the screw is a locating element that gets adjusted repeatedly. A cone point (DIN 914's territory on this site) digs in for maximum holding on soft shafts; a cup point (DIN 916) is the general-purpose compromise; a flat point (DIN 913) presses on finished surfaces. DIN 926 adds the slot drive, which is why it dominates the micro sizes in this ladder (M1-M6) where a hex socket key would be larger than the screw itself.
The thread tolerance prints as 6h at M1,4 but 6g from M1,6 — does that really matter at these sizes?
It does, because the difference scales with the thread. 6h is the tighter, no-allowance fit; 6g carries a small diameter allowance that makes coating and assembly easier. On an M6 thread the allowance is a rounding error against the joint; on M1,4 it is a meaningful fraction of the thread engagement, and it changes which nuts or tapped holes mate cleanly. The source splits the ladder exactly at the M1,4/M1,6 boundary, so a mixed-size assembly using these screws threads with two different fit classes — check the mating thread standard per size rather than assuming one tolerance across the ladder, and state the requirement on the RFQ if your assembly mixes them.
Brass as a printed option for a set screw — who actually uses that?
Three buyers, mostly. Electrical assemblies: brass does not magnetize and conducts, so brass set screws work as contact or grounding points and will not disturb magnetic sensors. Spark-risk environments: a brass point against steel cannot ignite a fuel-air mixture the way a sliding steel point can. Corrosion-adjacent assemblies: where an A1 stainless point would gall against an aluminium seat, brass slides. The trade-offs are mechanical — brass is soft, so clamping torque and point wear both limit it — which is why the steel 5.8 ladder remains the default and brass is the printed special case. The source prints no finishes for any family, so coated steel versions are a quotation item.
What should an RFQ for DIN 926 set screws state?
Thread size (M1-M6 from the ladder) and length l1 as a pair (neither l1 nor the pin length l2 is tabulated — the proportions come from the standard document, the length is your drawing's call), material family from the printed options (steel 5.8 / A1 stainless / brass), the thread tolerance matched to your mating thread (6h at M1,4, 6g from M1,6), slot acceptance if a powered driver is involved (n/t rows dimension the slot), quantity per size — and any finish (none printed). Sizes outside the ladder, other point styles, or non-printed material grades are confirmed at quotation.
Related knowledge
- Thread-Forming vs Thread-Cutting vs Thread-Rolling Self-Tapping Screws: What the Evidence Settles on Base Material
- Screw Family Selection by Base Material: Wood, Machine and Self-Tapping Threads, Engagement and Coating
- Hex Bolts vs Socket Head Cap Screws: What the Evidence Settles on Strength, Clearance and Cost
Request a Quote
Get factory-direct pricing from the manufacturer.
What to include in your DIN 926 Slotted Set Screws with Full Point (M1 – M6) inquiry
- ✓ Identify the screw type and standard, including head style and drive recess.
- ✓ Give nominal diameter, thread pitch, length and engagement or hole details where relevant.
- ✓ State the material/property class, substrate material and thickness, and required coating or finish.
- ✓ Describe installation, locking or removal requirements, quantity and destination.
- ✓ Factory-direct pricing for your DIN 926 Slotted Set Screws with Full Point (M1 – M6)
- ✓ Standard and custom specifications
- ✓ Factory-direct export to buyers in Europe, Asia, the Americas and the Middle East
- ✓ Full fastener family support